499150
15
Zoom out
Zoom in
Vorherige Seite
1/78
Nächste Seite
15
4.4 Emptying the dirt trap (2.10)
Always remove the upper part of the
vacuum cleaner before emptying the dirt
container!
- Open the vacuum cleaner,
- Raise the upper part slightly, depress the
support (2.5),
- Raise the upper part to the stop (vertical
position),
- Remove the upper part by moving it for-
wards horizontally,
- Empty the dirt container,
- Replace the upper part. Warning: Make
sure that both upper-part pins are fully
inserted in the recesses (1.5)!
- Close the vacuum cleaner.
4.5 Stand/Brake
The wheels can be blocked by the brakes
(2.8), thus preventing the vacuum cleaner
from rolling away unexpectedly.
4.6 Hose depot (partly in scope of
delivery)
Securing the hose depot on the dust extrac-
tor: see Fig. 4. When work is complete, you
can guide the extractor hose through the
opening (4.1) and deposit the hose in the
depot. Similarly, the mains cable can also
be guided through the opening (4.2) and
deposited in the hose depot.
5 Application
- A systainer can be xed to the storage
area (1.12) with the two clamps (1.10).
Tools or accessories can also be stowed
on the storage area and in the storage
compartments (1.6, not with CTM 22).
- A hose coupling (1.11) (487072) can be
plugged into the opening (1.8). The suc-
tion hose is connected to the tool from
above with the hose coupling. Alterna-
tively, a hose clip (452998) can be tted
for coiling the suction hose.
- The push handle (2.11) (452921; supplied
ready with CTM 44 and CTM 55) makes the
vacuum cleaner easier to move. Acces-
sories (e.g. vacuum accessories) can be
xed to the push handle batten (2.9).
- An air blast is obtained by inserting a suc-
tion hose in the blast opening (2.7).
5.1 Vacuuming dry materials
A lter bag must be used without
exception when evacuating noxious
substances!
Before using the vacuum cleaner to evacu-
ate dry substances, a lter bag must always
be inserted in the container.
Then the evacuated material can be dis-
posed of easily. The lter element becomes
damp after evacuating liquids. A damp lter
element suffers more wear and tear if it
is used for dry materials. Accordingly, the
lter element should be dried or replaced
with a dry one before dry operation.
5.2 Vacuuming liquids
Do not evacuate combustible liquids!
If foam or liquid escapes, stop work
immediately and empty the dirt con-
tainer.
The lter bag has to be removed before
evacuating liquids. We recommend use of a
special wet lter. When the maximum lling
level is reached, a bag-full indicator (2.12)
automatically interrupts extraction.
5.3 Volume ow monitoring
If the air speed in the suction hose drops
below 20 m/s, an acoustic warning signal
sounds for safety reasons.
Possible causes and adjustments
Cause
- Adjustment
Suction force regulator (1.4) set to a
too low value
- Adjust suction force regulator to a higher
value
Rotary knob (1.2) not adjusted to the
connected hose diameter
- Adjust to correct hose diameter
Suction hose blocked or twisted
- Remove blockage or twist
Filter bag full
- Change lter bag
Filter element dirty
- Change lter element
- Only when operating without a lter bag:
clean lter element
Electronic monitoring system malfunc-
tioning
- Call Festool customer service for adjust-
ment
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool CTM 44 E wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info