778630
25
Zoom out
Zoom in
Vorherige Seite
1/142
Nächste Seite
The power tool can be placed down flat on
the dust extraction attachment when not in
use.
Remove the sanding tool from the power
tool for transport.
9.1 Abrasive cutting
Always guide the sanding tool through the
workpiece in a straight line.
Ensure that the sanding tool does not tilt
and that it is not loaded at an angle or from
the side.
Ensure that the plate lies flat on the work
piece.
9.2 Cuts near edges [6]
WARNING
Risk of injury from exposed sanding tools
With the exception of cuts near edges, the
dust extraction attachment must only be
used in the locked position and with the
auxiliary handle.
Remove the auxiliary handle.
Check to ensure that the moving part of the
dust extraction attachment can be moved
freely using the retractor lever and that it
automatically returns to its starting posi
tion.
Hold the power tool in your right hand.
Switch on the power tool and position it
on the workpiece.
Unlock the retractor lever [6-1] for the
dust extraction attachment with your left
hand just before you reach the wall.
Use the retractor lever to retract the
moving part of the dust extraction attach
ment while continuing to cut so that you can
get as close to the wall as possible.
This ensures that the dust extraction sys
tem delivers maximum performance.
After the cutting work is complete, return
the dust extraction attachment to its start
ing position using the retractor lever.
10 Acoustic warning signal
If the power tool switches off because of subse
quent operating statuses, no warning signal
sounds when it switches on.
Battery pack not accepted
Insert the correct battery pack model.
Battery pack empty
Change the battery pack.
Charge the battery pack.
Battery pack fault
Change the battery pack.
Use the charger to check that the battery
pack is fully functional once it has cooled
down.
Battery pack overheated
Let the battery pack cool down.
Power tool overheated
The power tool must cool down before it
can be started again.
Power tool fault
Contact a Festool service workshop or spe
cialist dealer.
Power tool jammed
Eliminate the cause of the jam.
If the power tool switches off when it be
comes jammed, no warning signal sounds.
11 Accessories
Always use original Festool tools and accesso
ries. Using low-quality tools or accessories
from other manufacturers may increase the
risk of injury and seriously unbalance the ma
chine, decreasing the quality of the working re
sults and accelerating power tool wear.
Refer to the Festool catalogue for the order
numbers of accessories and tools or find them
online at www.festool.co.uk.
12 Service and maintenance
WARNING
Risk of injury, electric shock
Always remove the battery pack from the
power tool before performing any mainte
nance or service work.
All maintenance and repair work that re
quires the power tool to be opened up
should always be carried out by an author
ised service workshop.
Customer service and repairs must
only be carried out by the manufac
turer or service workshops. Find the
nearest address at:
www.festool.co.uk/service
Always use original Festool spare
parts. Order no. at:
www.festool.co.uk/service
EKAT
1
235
4
English
25
25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool DSC-AGC 18 FH wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info