Bedienungsanleitung Festool es 150 5 eq plus (Seite 7 von 50) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

389524

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

1 Before using sander

1.1 Safety instructions

Read the safety instructions on the

attached sheet before using the sander.

Always wear protective goggles

because of possible dangers when

sanding.

The manufacturers handling and processing

instructions must be observed without fail if

explosive or self-igniting dusts are likely to

occur during sanding.

The electric tool must be connected to a suitable

dust extraction unit and applicable safety

regulations must be observed if dusts

dangerous to health are likely to occur during

sanding.

Wear a dust mask for your own safety.

1.2 Correct usage

The sanders are designed for sanding wood,

plastic, composite materials, paint / varnish,

filling material and similar materials.

Metal and materials with an asbestos content

must not be processed with these tools.

The machines must not be damp nor operated

in a damp environment for electrical safety

reasons. The machines may only be used for

dry sanding.

The user bears sole responsibility for any

damage or accidents resulting from incorrect

use.

1.3 Noise and vibration information

Typical values established in compliance with

EN 50 144:

Sound pressure level 70 dB(A)

Measured acceleration

ES 150/3 EQ 4.0 m/s²

ES 150/5 EQ 6.0 m/s²

The noise level can exceed 85 dB(A)

during work.

Wear ear protectors!

2 Electrical connection and operation

The mains voltage must

correspond with the voltage on the

rating plate!

Switch (1.2) is an on/off switch.

For continuous use it can be engaged with the

lateral locking button (1.3). Pressing the switch

again releases the lock.

See Fig. 3 for connection and disconnection of

the power cable.

3 Electronic control

The ES 150/3 EQ, ES 150/5 EQ has an

electronic control with which the

rotational speed can be varied step-

free.

This allows the sanding speed to be adapted to

the optimum level according to the material

concerned. The speed is set using the rotary

control button (1.1).

The numbers on the rotary control button

represent approximately the following stroke/

orbit speeds:

4 Dust extraction

Dust extractors prevent large

accumulations of dust in the air in the

working environment and dirt collecting

in the workplace.

4.1 Inboard extraction

The machines are fitted with inbuilt extraction

as standard.

Technical data ES 150/3 EQ ES 150/5 EQ

Wattage 310 W 310 W

Speed 4,000 - 10,500 rpm 4,000 - 9,000 rpm

Power stroke 8,000 - 21,000 rpm 8,000 - 19,000 rpm

Sanding stroke 3.0 mm 5.0 mm

Sanding base Æ 150 mm Æ 150 mm

Weight 1.8 kg 1.8 kg

Degree of protection / II / II

The specified illustrations can be found at the beginning of the operating instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool es 150 5 eq plus Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info