Bedienungsanleitung Festool HK 55 EQ (Seite 23 von 143) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

778533

Zoom out

Zoom in

Vorherige Seite

1/143

Nächste Seite

[1-9] Split scale for cutting depth stop

(with/without guide rail)

[1-10] Extractor connector

[1-11] Angle scale

[1-12] Knob for angle setting

[1-13] Cutting depth adjuster

[1-14] Mains power cable

[1-15] Adjustable jaws

[1-16] Speed control

The illustrations specified are located at the be

ginning and end of the operating instructions.

6 Operation

WARNING

Unauthorised voltage or frequency.

Risk of accidents

► The mains voltage and the frequency of the

power source must correspond to the

specifications on the name plate.

► In North America, only Festool machines

with the voltage specifications 120 V/60 Hz

may be used.

CAUTION

Heating of the Plug it connection if bayonet

fitting is not completely locked

Risk of burns

► Before switching on the power tool, make

sure that the bayonet fitting at the mains

cable is closed fully and locked.

Always switch off the machine before

connecting and disconnecting the mains

power cable.

Connecting and detaching the mains power ca

ble [1-14] see Fig. [2].

6.1 Switch on/off

► Slide switch-on lock [1-2] upwards.

► Press the ON/OFF switch [1-7].

Press = ON

Release = OFF

7 Settings

WARNING

Risk of injury, electric shock

► Always pull the mains plug out of the sock

et before performing any type of work on

the machine!

7.1 Electronics

Smooth start-up

The electronically controlled smooth start-up

function ensures that the power tool starts up

smoothly.

Speed control

You can regulate the speed steplessly within

the speed range using the adjusting

wheel [1-16] (see chapter 4). This enables you

to optimise the cutting speed to suit the surface

(see chapter 8.4).

Current limiting

Current limiting prevents excessive current

consumption under extreme overload, which

can lead to a decrease in the motor speed. The

motor immediately restarts after the load is re

moved.

Brake

The HK 55 EBQ is fitted with an electronic

brake. When the saw is switched off, the saw

blade slows to a stop electronically within ap

prox. 2 seconds.

Restart protection

The integral restart protection prevents the

electric power tool from automatically starting

up again after an interruption in power when

the ON/OFF switch is pressed. In this case the

electric power tool must be switched off and

then switched back on again.

Temperature cut-out

When exceeding a certain engine temperature

level, the machine power supply and speed are

capped. The power tool continues operating at

reduced power to allow the ventilator to cool

the motor rapidly. The power tool resumes to

full performance automatically once the motor

has cooled sufficiently.

7.2 Adjusting the cutting depth

The cutting depth can be set at 0 – 55 mm.

► Press cutting depth adjustment [3-1].

► Pull up or push down saw at main handle.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool HK 55 EQ Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info