Bedienungsanleitung Festool HK 85 EB (Seite 23 von 164) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

778534

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

6.1 Switch on/off

► Slide switch-on lock [1-2] upwards.

► Press the ON/OFF switch [1-8].

Press = ON

Release = OFF

7 Settings

WARNING

Risk of injury, electric shock

► Always disconnect the mains plug from the

socket before performing any work on the

machine.

7.1 Electronics

Smooth start-up

The electronically controlled smooth start-up

function ensures that the power tool starts up

smoothly.

Speed control

You can continuously adjust the speed within

the speed range using the adjusting

wheel [1-17] (see "Technical data"). This ena

bles you to optimise the cutting speed to suit

each surface.

Speed range per material

Solid wood (hard, soft) 6

Chipboard and hardboard 3–6

Laminated wood, blockboard, veneered

and laminated panels 6

Laminate, mineral materials 4–6

Plaster- and cement-bonded chipboard

and fibreboard 1–3

Aluminium panels and profiles up to

15 mm 4–6

Plastics, fibre-reinforced plastics, paper

and fabric 3–5

Acrylic glass 4–5

Current limiting

Current limiting prevents excessive current

consumption under extreme overload, which

can lead to a decrease in the motor speed. The

motor immediately restarts after the load is re

moved.

Brake

The HK 85 EB comes with an electronic brake.

The saw blade is stopped electronically within

approximately two seconds of switching off the

machine.

Temperature cut-out

The power supply is restricted and the speed

reduced if the motor exceeds a certain temper

ature. The power tool continues operating at re

duced power to allow the ventilator to cool the

motor quickly. The power tool starts up again

automatically once the motor has cooled suffi

ciently.

7.2 Adjusting the cutting depth

The cutting depth can be set to between 0 and

86 mm.

► Press cutting depth adjustment [2-1].

► Pull up or push down saw at main handle.

Cutting depth without guide rail/track

rail

max. 86 mm

+FS

Cutting depth with guide rail/track rail

max. 82 mm

7.3 Adjusting the cutting angle

The saw table must be on an even surface

when adjusting the cutting angle.

Between 0° and 60°:

► Open knob [3-2].

► Swivel sawing unit to the desired cutting an

gle [3-1].

► Close knob [3-2].

Both positions (0° and 60°) are set at the

factory and can be readjusted by the after-

sales service team.

For angled cuts, the cutting depth is

smaller than the value displayed on the

cutting depth scale.

7.4 Adjust pendulum guard

Risk of injury! Sharp edges! The pendu

lum guard swings back quickly in the

event of sudden release.

The pendulum guard [1-6] must only be opened

with the retractor lever [1-4].

7.5 Selecting the saw blade

Festool saw blades are identified by a coloured

ring. The colour of the ring represents the ma

terial for which the saw blade is suited.

WARNING! Risk of injury! Pendulum hood

mechanism not working correctly! Diamond

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool HK 85 EB Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info