Bedienungsanleitung Festool HK132 (Seite 18 von 114) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

573118

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

forces can be controlled by the operator, if proper

precautions are taken.

b) When blade is binding, or when inter rupting a

cut for any reason, release the trigger and hold

the saw motion less in the material until the

blade comes to a complete stop. Never at tempt

to remove the saw from the work or pull the saw

backward while the blade is in motion or kick-

back may occur. Investigate and take cor rective

actions to eliminate the cause of blade binding.

c) When restarting a saw in the work piece, cen-

tre the saw blade in the kerf and check that saw

teeth are are not engaged into the material. If

saw blade is binding it may walk up or kickback

from the workpiece as the saw is restarted.

d) Support large panels to minimise the risk of

blade pinching and kickback. Large panels tend

to sag under their own weight. Supports must be

placed under the panel on both sides, near the

line of cut and near the edge of the panel.

e) Do not use dull or damaged blades. Unsharpened

or improperly set blades produce narrow kerf

causing excessive friction, blade binding an kick-

back.

f) Blade depth and bevel adjusting lock ing levers

must be tight and secure before making cut.

If blade adjustment shifts while cutting, it may

cause binding and kickback.

g) Use extra caution when making a “plunge cut”

into existing walls or other blind areas. The pro-

truding blade may cut objects than can cause

kick back.

5.4 Speciﬁc Safety Rules for HK 132 E Circular

Saws

Lower guard function

a) Before each use, check if the retract ing blade

guard closes properly. Do not operate the saw if

the retracting blade guard does not move freely

and retract immediately. Never clamp or tie the

retracting blade guard in the open position. If the

saw is accidentally dropped, the retracting blade

guard can be bent. Pull back the retracting blade

guard with the pull-back lever and ensure that it

moves freely and does not touch the saw blade or

other parts at any cut ting angles and depths-of-cut.

b) Check the spring function of the re tracting

blade guard. If the retract ing blade guard and

the spring do not operate properly, have the

machine serviced before using. The retracting

blade guard may operate sluggish due to dam-

aged parts, gummy deposits or build-up of chips/

sawdust.

c) Only pull back the retracting blade guard manu-

ally for special cuts, such as “plunge and bevel

cuts”. Pull back the retracting blade guard with

the pull-back lever and release it as soon as the

saw blade has penetrated the work. For all other

sawing jobs, the re tracting blade guard must op-

erate auto matically.

d) Do not place down the saw on a work bench or

the ground without the re tracting blade guard

covering the saw blade. An unprotected, coast-

ing saw blade will move the saw in the op posite

direction of the cut, cutting what ever is in its path.

Pay attention to the run-on period of the saw.

Riving knife function

a) Use the matching riving knife for the saw blade

being worked with. The riving knife must be wid-

er than the thick ness of the blade back, but thin-

ner than the kerf width of the saw blade.

b) Adjust the riving knife as described in the oper-

ating instructions. Incor rect width, position and

alignment can be the cause that the riving knife

does not effectively prevent kickback.

c) Always use the riving knife, except when per-

forming plunge cuts. After the plunge cut, mount

the riving knife again. The riving knife interferes

when performing plunge cuts and can lead to

kickback.

d) In order for the riving knife to be ef fective, it

must be located in the cut. For short cuts, the riv-

ing knife is ineffec tive for the prevention of kick-

back.

e) Do not operate the saw with a bent riving knife.

Even a minor malfunction can lead to sluggish re-

traction of the re tracting blade guard.

- Only for AS/NZS: The tool shall always be sup-

plied via residual current device with a rated

residual current of 30 mA or less.

5.5 Emission levels

Levels determined in accordance with EN 60 745

are typically:

Sound pressure level L

= 102 dB (A)

Sound-power level

= 113 dB (A)

Uncertainty K = 3 dB

CAUTION

The noise produced during work can damage

your hearing.

 Always use ear protection.

Vibration emission value a

(vector sum for three

directions) and uncertainty K measured in accord-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool HK132 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info