Bedienungsanleitung Festool HK132E (Seite 20 von 114) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

573119

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

switches the motor off before the motor is able to

reach a critical temperature. After a cooling period

of approx. 3–5 minutes the machine is once again

ready for operation and can run at full load. The

cooling period can be greatly reduced if the ma-

chine is running (idling or recovery speed).

7.2 Cutting Depth Adjustment

Release the locking lever [1-16].

Set the required depth on the cutting depth scale

[1-15].

Raise: smaller cutting depth

Lower: larger cutting depth

Re-tighten the clamping lever [1-16]

To achieve the best cutting results, the saw blade

should protrude from the material by no more than

3 mm.

7.3 Cutting Angle Adjustment

Release the cutting angle locking lever at [1-7] and

[1-18].

Set the cutting angle as required using the scale

[1-19]. (The scale is calibrated in 1° increments).

Re-tighten the cutting angle locking lever at [1-7]

and [1-18].

WARNING

The maximum cutting depth is reduced for

bevel cuts.

7.4 Cut indicator

The cut produced by the HK 132 E depends on the

bevel setting and can be observed at the cut indica-

tor.

7.5 Parallel Guide

Various parallel guides can be inserted into the ma-

chine base plate [2-2] on the left [2-3] and on the

right [2-4].

Tighten the parallel guide using the winged screws

[2-1].

7.6

Dust extraction

CAUTION

Inhaled dust may damage the air pas sages.

 Tools should be permanently connected to

the dust extracting plant.

 Wear respirator if you work with dust.

To extract dust, suction adapter [1-1] can be mount-

ed on the sawdust ejector through which common

extract hoses of dust extractors can be connected.

7.7 Replacing the Saw Blade

WARNING

Risk of injury

 Before exchanging the saw blade, pull the

mains plug from the power sup ply socket.

 Wear protective gloves!

The sawing performance and the quality of the

cut depend essentially on the condition and tooth

form of the saw blade. Therefore, use only sharp

saw blades that are suitable for the material to be

worked.

Swing back the swinging guard with the lever [3-5].

Install a suitable saw blade according to the illus-

tration and tighten. Take care that the mounting

ﬂange [3-4] and the clamping ﬂange [3-2] are cor-

rectly positioned. The holes in the saw blade [3-3]

must ﬁ t onto the follow-up pins on the mounting

ﬂ ange [3-4].

WARNING

Risk of injury

 Observe for installation: The cutting direction

of the teeth (arrow on the saw blade) must

match the direction of the arrow on the guard.

 Check the function of the swinging guard.

Tighten the hexagon bolt [3-1] using the SW19 Allen

key supplied, while holding the clamping ﬂ ange

[3-2] with the single ring spanner which is also sup-

plied.

To remove the blade, follow the same sequence in

reverse.

8 Operating Instructions

- Do not cut into nails, screws, etc.

- Do not work with materials containing asbestos.

- Do not use saw blades that have cracks or that

are damaged.

- Under no circumstances use abrasive disks!

- Saw blades of highly alloyed, high-speed steel

(HSS-steel) must not be used.

- Feeding too fast signiﬁ cantly reduces the per-

formance of the machine and short ens the life

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool HK132E Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info