Bedienungsanleitung Festool HKC 55 EB (Seite 23 von 143) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

778531

Zoom out

Zoom in

Vorherige Seite

1/143

Nächste Seite

[1-3] Lever for changing blades

[1-4] Retractor lever for pendulum guard

[1-5] Guide wedge

[1-6] Pendulum guard

[1-7] On/Off switch

[1-8] Lever for plunge function

[1-9] Split scale for cutting depth stop

(with/without guide rail)

[1-10] Extractor connector

[1-11] Angle scale

[1-12] Knob for angle setting

[1-13] Cutting depth adjuster

[1-14] Capacity display button on battery

pack

[1-15] Capacity display

[1-16] Battery pack

[1-17] Button for releasing the battery pack

[1-18] Adjustable jaws

The specified illustrations appear at the begin

ning of the Operating Instructions.

Accessories shown or described are not always

included in the scope of delivery.

6 Battery pack

Before using the battery pack, check that the

battery interface is clean. Any contamination of

the battery interface may impair correct contact

and lead to the contacts being damaged.

A faulty contact may result in the machine over

heating or being damaged.

[2A] Remove the battery pack.

[2B]

klick

Insert the battery pack – until it

clicks into place.

Further information about the charger and

battery pack with capacity indicator can be

found in the corresponding operating

manual.

7 Settings

WARNING

Risk of injury, electric shock

► Always disconnect the battery packs from

the machine before performing any type of

work on the machine!

7.1 Electronics

Smooth start-up

The electronically controlled smooth start-up

ensures that the machine starts up jolt-free.

Constant speed

The motor speed remains constant through

electronic control to ensure a uniform cutting

speed even when under load.

Current limiting

Current limiting prevents excessive current

consumption under extreme overload, which

can lead to a decrease in the motor speed. The

motor immediately restarts after the load is re

moved.

Brake

The HKC 55 EB is fitted with an electronic

brake. When the saw is switched off, the saw

blade slows to a stop electronically within ap

prox. 2 seconds.

Restart protection

The integral restart protection prevents the

electric power tool from automatically starting

up again after an interruption in power when

the ON/OFF switch is pressed. In this case the

electric power tool must be switched off and

then switched back on again.

Temperature cut-out

When exceeding a certain engine temperature

level, the machine power supply and speed are

capped. The power tool continues operating at

reduced power to allow the ventilator to cool

the motor rapidly. The power tool resumes to

full performance automatically once the motor

has cooled sufficiently.

7.2 Adjusting the cutting depth

The cutting depth can be set at 0 – 55 mm.

► Press cutting depth adjustment [3-1].

► Pull up or push down saw at main handle.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool HKC 55 EB Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info