Bedienungsanleitung Festool IS330EB (Seite 27 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

573136

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

or with a dysfunctional lubricating system, the oil

feed pump will be damaged, as well as the tool’s

entire cutting assembly!

The oil reservoir cap [1-9] has an opening with a

one-way suction valve for air pressure compensa-

tion. If you use the machine in other than the verti-

cal position, the chain may not get lubricated. The

outlet of the oil reservoir is located down at the

back, and when the machine rotates, the pump

is not able to suck up the oil. The quantity of oil

in the reservoir is indicated by the level in the oil

gauge [1-8].

8.3 Electrical connection

WARNING

If the tool is used with an incorrect power supply,

there is a risk of injury.

The IS 330 EB insulation saw can only be connect-

ed to a single-phase power supply with 220-240V/

50/60Hz alternating current. The machine has a

class II protective covering according to EN 60 745-1

and has noise suppression according to EN 55 014.

Before operating the machine, make sure that the

voltage of the socket corresponds to the voltage

information stated on the label of the machine.

The portable cord can be extended in the following

manner, if necessary:

- Length 20 m, cross-section of wires 3 × 1.5

- Length 50 m, cross-section of wires 3 × 2.5

Use only appropriately marked extension cords

intended for use outdoors.

9 Operation

WARNING

Risk of accident, electric shock

 Always pull the plug out of the socket before

performing any type of work on the machine.

9.1 Switching on and off

Before switching the machine on, tighten all

clamping and ﬁ xing bolts. Handle the machine

with both hands, and put it on the cutting piece

so that the chain is loose and will not stick inside

the cut after activation.

To turn on

Press the unlocking button [1-1] on the top of the

handle and hold it; then press the motor switch

button [1-2].

To turn off

Let up on the motor switch button [1-2]. The un-

locking button [1-1] will return to its initial posi-

tion and prevent an unwanted start-up. When the

machine is turned off, an electric brake activates

and signiﬁ cantly shortens the run-down time of

the chain.

Do not remove the machine from the cutting piece

until the chain is at a standstill.

9.2 Controlling chain and guide bar lubrica-

tion

The quantity of lubricating oil can be controlled

using a feed pump [5-2]. When you press the feed

pump, [5-2] the 0, 1, 2 and MAX positions can be

set at a notch [5-1]. Position 0 ensures minimum

lubrication for clean cuts, but must not be used

permanently, and after such cuts the chain and

plate must be lubricated with an increased quan-

tity. For permanent operation the quantity should

be set to level 2 and MAX.

9.3 Cut indicator

When cutting without the guide rail, adjust the

chain’s internal cutting plane using all of the in-

dicators on the guide runner:

- Indicator 0° [4-1] for rectangular cuts

- For bevel cuts:

• indicator 45° [4-4]

• indicator 60° [4-5]

To determine the chain’s external cutting plane,

use cutting proﬁ le indicators [4-6].

For cutting with the guide rail (GRP 800/1400/

3000-2; Fig. [8]), adjust the chain’s inner cutting

plane using only cut indicator 0° [4-1].

9.4 Guide ruler

Slide the guide ruler [1-3] into the holders in the

runner [1-6] and secure it with the hand screws

[1-5]. The guide ruler allows parallel cuts along

an even edge.

9.5 Exhaust

WARNING

Dust hazard

 Dust can be hazardous to health. Always

workwith a dust extractor.

 Always read applicable national regulations

be-fore extracting hazardous dust.

10 Accessories

On the bottom part of the suction runner, the

machine has a longitudinal groove for mounting

on the guide rail. Thus larger dimensions can be

made more easily and more precisely.

10.1 The guide system

When cutting larger work pieces, and to

achieve accurate angled cuts, use of the

guide system is recommended for easy and safe

handling.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool IS330EB Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info