Bedienungsanleitung Festool KS KAPEX 88 E (Seite 18 von 138) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

497998

Zoom out

Zoom in

Vorherige Seite

1/138

Nächste Seite

5.3 Emission levels

Levels determined in accordance with EN 61029

are typically:

Sound pressure level 88 dB(A)

Noise level 101 dB(A)

Measuring uncertainty allowance K = 3 dB

Wear ear protection.

Measured acceleration < 2.5 m/s²

The emission values speciﬁ ed (vibration, noise)

were measured in accordance with the test con-

ditions stipulated in EN 61029 and are intended

for machine comparisons. They are also used for

making preliminary estimates regarding vibration

and noise loads during operation.

The emission values speciﬁ ed refer to the main

applications for which the power tool is used. If

the electric power tool is used for other applica-

tions, with other tools or is not maintained suf-

ﬁ ciently prior to operation, however, the vibration

and noise load may be higher when the tool is

used. Take into account any machine idling times

and downtimes to estimate these values more

accurately for a speciﬁ ed time period. This may

signiﬁ cantly reduce the load during the machine

operating period.

6 Commissioning

Warning

• Observe the mains voltage: The voltage and

frequency of the power source must comply with

the speciﬁ cations on the machine's identiﬁ ca-

tion plate.

• In North America, only Festool machines with

the voltage speciﬁ cations 120 V/60 Hz may be

used.

Prior to initial operation:

– Remove the transport safety device (4.4) from

the guide rod.

On/Off switch

– Press the on/off switch (1.2) as far as possible

to unlock the saw unit and the pivot guard.

– Press the switch-on lock (1.3).

– Press the on/off switch (1.2) all the way in to

start the machine.

– Release the on/off switch again to switch off the

machine.

7 Adjustments

Always pull the plug out of the socket

before performing any type of work on

the machine.

KS 120 EB only: Replace the laser warning sticker

(3.1) with the relevant accompanying warning

sticker in your language.

7.1 Transport

Securing the machine (transport position)

– Press the on/off switch (4.1).

– Swivel the saw unit downwards until it reaches

the fence.

– Press the lock (4.2). The saw unit now remains

in the lower position.

– Tighten the rotary knob (4.3) to secure the saw

unit in the rear position.

– Wind up the mains cable into the cable holder

(5.5) before transporting.

– Stow away the Allen key (5.4) and the bevel (5.3)

(KS 120 EB only) in the holders provided.

Never carry or lift the machine by the

movable pivot guard (5.1).

Carry the machine by the edge of the saw table

(5.2) and the handle (5.5) in the cable holder.

Unlocking the machine (working position)

– Push the saw unit down slightly and remove the

transport safety device (4.2).

– Swivel the saw unit upwards.

– Unscrew the rotary knob (4.3).

7.2 Mounting the machine

Always pull the plug out of the socket

before performing any type of work on

the machine.

Before using the machine, set up on a level, stable

work surface (e.g. the underframe UG-KAPEX, the

multifunction table MFT or a worktop).

The following assembly options are available:

Fastening: Secure the machine on the work sur-

face using four screws. Use the holes (6.1) on the

four support points on the saw table.

Clamps: Secure the machine on the work surface

using four clamps. The ﬂ at surfaces (6.2) on the

four saw table support points are used as clamp-

ing surfaces.

Clamping set (for MFT): Secure the machine on

the Festool multifunction table MFT using the

clamping set (6.4, 494693). Use the two screw

holes (6.3).

Underframe UG-KAPEX

Secure the machine on the underframe as de-

scribed in the assembly instructions enclosed

with the underframe.

7.3 Changing tools

Risk of accidents

• Always pull the mains plug out of the socket

before changing blades.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool KS KAPEX 88 E Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info