Bedienungsanleitung Festool LC 45 QUICKLADER (Seite 6 von 34) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

574949

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

Technical data Charger LC 45

Supply voltage (input) 230 - 240 V~

Line frequency 50/60 Hz

Charging voltage (output) 7.2 - 18 V=

Charging current 3 A

Quick charge max. 3 A

Compensation charge

pulsating app. 0.06 A

Charging time for

NiCd 2.0 Ah app. 45 min

NiCd 2.4 Ah app. 50 min

NiMH 3.0 Ah app. 70 min

The speciﬁ ed illustrations can be found

at the beginning of the operating instruc-

tions.

1 Before starting up, please obser-

ve the following

1.1 Intended use

The LC 45 battery charger is designed for

recharging the battery pack listed.

The user is liable for damage and injury

resulting from incorrect usage!

1.2 Safety instructions

- Repairs may only be performed by autho-

rised technicians. LC 45 charging device:

Even after disconnection from the mains,

there is still a high capacitor voltage on

the power output component on the inside

of the device.

- Protect equipment against moisture.

- Do not use the charger if the connecting

cable is damaged.

- Protect the cable against heat, oil and

sharp edges.

- Keep the connection contacts of electro-

nic equipment, charger and battery pack

clean.

- Keep the air vents of the electronic equip-

ment and the charger clean to guarantee

the air circulation for cooling.

- No metal objects (metal chips) should

enter the charger at the contact points as

well as through the cooling slits into the

equipment (danger of short circuit).

1.3 Wall mounting LC 45

The charger LC 45 has two longitudinal slots

on its rear by which it can be suspended on

walls using two screws (e.g. button-headed

or ﬂ at head screw with a shaft diameter of

5 mm).

Screw both screws into the wall 96 mm

apart until the screwhead is protruding from

the wall by approx. 4 mm.

2 Charge battery pack

To load the battery pack, push it into the

holder (1.1) on the charger up to the

stop.

Perform this in reverse to remove the bat-

tery pack from the charger.

The battery type used (NiCd or NiMH) is

detected automatically.

Charging is controlled by a microproces-

sor. If a warm NiMH battery pack (>37

°C) is inserted, charging will only be carried

out at a lower charge current. In this case,

the charging time is extended.

We reserve the right to make changes to

the technical data contained in this infor-

mation as a result of ongoing research and

development work.

The LED (1.2) indicates the respective char-

ging state of the charger.

LED yellow – steady

Charger is ready for use

LED green – ﬂ ashing

Battery pack being charged.

LED green – steady

Battery pack fully charged, conservation

charge on.

LED red – ﬂ ashing

General malfunction, e. g. full contact not

being made, short-circuit, battery pack

faulty.

LED red – steady

Temperature of battery pack is outside per-

missible limit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool LC 45 QUICKLADER Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info