Bedienungsanleitung Festool LEX 3 125 5 (Seite 16 von 101) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

499938

Zoom out

Zoom in

Vorherige Seite

1/101

Nächste Seite

LEX 3

stored in a dry, inaccessible or locked loca-

tion, out of the reach of children.

–

Do not use the compressed air hose for

purposes for which it was not intended.

Protect the compressed air hose from heat,

oil and sharp edges. Check the compressed

air hose regularly and if it becomes damaged,

have it replaced by an approved specialist.

The compressed air hose cannot be used for

application devices such as atomising and

spraying equipment as the safety require-

ments against electrical hazards cannot be

satisfied.

–

Take good care of your tools.

Keep the

tools sharp and clean to enable better and

safer work. Follow the maintenance regula-

tions and the information about tool replace-

ment. Keep handles dry and free of oil and

grease.

–

Do not leave any tool key inserted.

Be-

fore switching on check that key and adjust-

ment tools are removed.

–

Avoid unintended start-up

. Do not carry a

compressed air tool that is connected to a

compressed air supply with your finger on the

trigger. When connecting the compressed air

hose to a compressed air supply, make sure

that the switch is not activated.

–

Be alert!

Pay attention to what you are do-

ing. Always work with care.

Do not use the compressed air tool if you are

not able to concentrate properly.

–

Have

your compressed air tool repaired by a

qualified specialist.This compressed air tool

corresponds to the relevant safety regula-

tions. Repairs should only be carried out by a

qualified specialist. The operator is otherwise

at risk of an accident.

–

Only work with correctly processed

compressed air.

Using the Festool supply

unit VE guarantees this.

5.2 Other risks

In spite of compliance with all relevant design

regulations, dangers may still present them-

selves when the machine is operated, e.g.:

– Workpiece parts being thrown off,

– Parts of damaged tools being thrown off,

– Noise emissions,

– Dust emissions.

5.3 Emission levels

Levels determined in accordance with EN ISO 15744/ISO 28927 are typically:

*For information: According to the old EN ISO 8662.

The specified emissions values (vibration,

noise)

– are used to compare machines.

– They are also used for making preliminary

estimates regarding vibration and noise

loads during operation.

– They represent the primary applications of

the power tool.

Increase possible for other applications, with

other insertion tools or if not maintained ad-

equately. Take note of idling and downtimes

of machine!

Version Sound pressure level /

Sound power level

Vibration emission level

3 directions 1 direction*

PFA

/ L

Uncertainty a

Uncer-

tainty K

Uncertainty

[dB(A)] [m/s²] [m/s²] [m/s²] [m/s²]

LEX 3 77/2,5 72 / 83 3 < 2,5 3,0 < 2,5 3,0

LEX 3 125/3 70 / 81 3 4,4 1,5 < 2,5 1,5

LEX 3 125/5 72 / 83 3 5,0 1,5 < 2,5 1,5

LEX 3 150/3 72 / 83 3 3,7 3,0 < 2,5 3,0

LEX 3 150/5 72 / 83 3 3,9 3,0 2,7 3,0

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool LEX 3 125 5 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info