778810
22
Zoom out
Zoom in
Vorherige Seite
1/172
Nächste Seite
[1-8] Handle
[1-9] Speed control
[1-10] Plug-it connection
[1-11] Extractor connector
[1-12] Suction sleeve stop
[1-13] Locking lever
[1-14] Extension tube
[1-15] Suction regulator
[1-16] Sanding head
[1-17] Surface control light
[1-18] Backing pad
[1-19] Interface pad
[1-20] Plug-it mains power cable
[1-21] Insulated gripping surfaces
The illustrations specified are located at the be
ginning and end of the operating instructions.
6 Commissioning
WARNING
Risk of injury, electric shock
Always disconnect the mains plug from the
socket before performing any work on the
machine.
6.1 Assembling/disassembling
WARNING
Incorrect installation
Risk of injury from falling parts and loss of
control
Before switching on the power tool, make
sure that all locking levers are completely
closed.
Assembly [2]
The long-reach sander consists of a
LHS 2 225 EQI or LHS 2 225 EQ handle [1-1], a
maximum of two extension tubes VL-
LHS 2 225 [1-14] and a sanding head HE-
LHS 2 225 [1-16].
Push the pipe end of the sanding head
into the opening on the handle as far as it
will go.
Turn the locking lever [2-1] towards the
sanding head as far as it will go.
Check whether the handle and sanding
head are firmly connected by pulling them
apart.
The handle and sanding head are securely con
nected.
Assemble the extension tubes in the same way
as the handle.
Disassembling [3]
Open the locking lever [3-1].
Turn the locking lever [3-1] further to
wards the end of the handle as far as it will
go and hold it in this position. Pull the sand
ing head and handle apart at the same time.
The sanding head and handle are separate and
can be stored in a Systainer.
Disassemble the extension tubes in the same
way as the handle.
6.2 Connecting
WARNING
Unauthorised voltage or frequency.
Risk of accidents
The mains voltage and the frequency of the
power source must correspond to the
specifications on the name plate.
In North America, only Festool machines
with the voltage specifications 120 V/60 Hz
may be used.
CAUTION
Heating of the Plug it connection if bayonet
fitting is not completely locked
Risk of burns
Before switching on the power tool, make
sure that the bayonet fitting at the mains
cable is closed fully and locked.
Connect and disconnect the mains power
cable - [4].
To connect the suction hose [5], see also
Section 7.6.
Using a special vacuum sleeve, the PLANEX
suction hose guarantees a permanent fixing
and better protection against kinking.
6.3 Switching on/off
On/off switch [1-5]
I = ON, 0 = OFF
English
22
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool LHS 2 225 EQ PLANEX wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info