778809
24
Zoom out
Zoom in
Vorherige Seite
1/172
Nächste Seite
Tighten all screws clockwise in a
crosswise sequence and check that they are
securely in place.
7.5 Adjusting the suction power
The long-reach sander can adhere itself to the
sanding surface, which helps you work more ef
fortlessly.
Set a low suction power.
First, switch on the power tool and then
place it on the sanding surface.
Slowly increase the suction power until a
noticeable application pressure is reached.
The suction regulator [1-15] can be
used to adjust the suction power
according to the sanding surface.
Ceiling
Maximum suction power
Wall
Minimum suction power
If the suction power is set too high, this
can lead to the power tool being overloa
ded, poor guidance or poor surface quality.
7.6 Dust extraction
WARNING
Health hazard posed by dust
Always work with an extractor.
Comply with national regulations.
Wear a dust mask.
The power tool does not have its own extractor
unit. A Festool mobile dust extractor with an
extractor hose diameter of 36 mm or 27 mm
should therefore be connected to the extractor
connector [1-11] (36 mm recommended due to
the reduced risk of clogging and higher suction
power).
Recommendation: Use an antistatic extractor
hose. This helps reduce the electric charge.
Always use the Festool CTL/M 36 E AC-
LHS or PLANEX mobile dust extractor for
the long-reach sander, as they are per
fectly designed for large quantities of dust
and have a dedusting system.
7.7 Adjusting the surface control light
The surface control light button [1-4] can be
used to switch the surface control light on and
off even when the power tool is switched off.
The surface control light switches off after one
hour when the power tool is switched off.
Controlling the surface control light via the
Festool Work app (only LHS 2 225 EQI)
If the power tool is connected to the
Festool Work app via Bluetooth® (see Sec
tion 7.8), the surface control light can be con
figured.
7.8 Connecting a power tool via Bluetooth®
(only LHS 2 225 EQI)
Connecting to the Festool Work app
The power tool can be configured with the
Festool Work app.
Press the Bluetooth® button [1-2] on the
power tool for approximately three seconds
until the LED display starts to flash blue.
For a period of 60 seconds, the power tool is
ready for connection.
Follow the instructions provided in the
Festool Work app to authorise the secure
connection.
By pressing the Bluetooth® button, you can
switch between the factory settings of the
power tool and the configurations in the
Festool Work app.
Connecting to the mobile dust extractor
Activate the mobile dust extractor's auto
matic mode (see the operating manual for
the mobile dust extractor).
Press the connection button on the mobile
dust extractor or on the remote control
once (see the operating manual for the mo
bile dust extractor/retrofit receiver mod
ule).
Switch on the power tool.
The mobile dust extractor starts up and the
power tool is connected until the mobile dust
extractor or the power tool is manually switch
ed off. If another power tool is connected via
Bluetooth® to the mobile dust extractor, the
connection is also lost.
LED indicator [1-3]
LED indicator Meaning
LED lights up
green. The configurations made in the
Festool Work app are active, e.g.
the surface control light has
been dimmed.
LED flashes
blue once. After being switched on, the
power tool searches for a mobile
dust extractor ready for connec
tion.
LEDs flash
blue. The power tool can be connected
to a mobile device.
English
24
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool LHS 2 225 EQI PLANEX wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info