Bedienungsanleitung Festool MCU 15 (Seite 8 von 38) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

497593

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

Technical data MCU 15

Supply voltage (input) 220 - 240 V ~

Line frequency 50/60 Hz

Charging voltage (output) 4.8 – 14.4 V (DC)

Charging current

• Quick charge max 7.5 A

• Compensation charge pulsating app.0.06 A

Charging time for

NiCd 1.2 Ah app. 11 min

NiCd 1.4 Ah app. 13 min

NiCd 1.7 Ah app. 16 min

NiCd 2.0 Ah app. 20 min

NiMH 3.0 Ah app. 70 min

Weight 0.9 kg

The illustrations mentioned can be found

on a fold-out page at the beginning of the

operating instructions.

1 Directions for use

The charger MCU 15 has been designed to

charge the battery packs speciﬁ ed under

Chapter 2.

The user will be liable for damage due to

improper use.

For your own safety

• Repairs may only be carried out by quali-

ﬁ ed experts. Warning: MCU 15 charging

device: Even after disconnection from the

mains, there is still a high capacitor volt-

age on the power output component on

the inside of the device.

• Protect equipment against moisture.

• Do not use the charger if the connecting

cable is damaged, unplug immediately

from the main.

• Protect the cable against heat, oil and

sharp edges.

• Never carry the tool by its cable and never

use to the cable to pull the plug out of the

wall socket.

• Do not use defect and damaged battery

packs.

• Only use original Festool battery packs.

Do not use spent and recycled battery

packs. The user shall be liable for dam-

ages if Festool original battery packs are

not used.

• Do not place spent battery packs into ﬁ re

or into domestic waste. Attention: Fes-

tool offers an ecological friendly waste

disposal for used battery packs (refer to

RECYCLING OF BATTERY PACKS).

• Do not open battery packs.

• Do not store battery packs with metal

objects (danger of short circuit).

• No metal objects (metal chips) should

enter the charger at the contact points as

well as through the cooling slits into the

equipment (danger of short circuit).

• Keep out of reach of children.

• Check the tool for damages before use.

Have damaged parts repaired or replaced

by the customer service department.

2 Charge battery pack

The charger MCU 15 can be used to charge

all Festool battery packs between 4.8 V and

14.4 V in the battery chamber (1.1).

The battery type used (NiCd or NiMH) is

detected automatically. Charging is control-

led by a microprocessor.

Warning: If a warm NiMH battery pack

(>37°C) is inserted, charging will only be

carried out at a lower charge current.

In this case the charging time for a battery

pack with 3.0 Ah is around 100 min..

The following NiCd-battery packs can also

be charged in the battery chamber (1.2):

Bosch 7.2 V Part No. 260 73 00001

7.2 V Part No. 260 73 35020

9.6 V Part No. 260 73 00002

12.0 V Part No. 260 73 00000

AEG 7.2 V Part No. 318 460

9.6 V Part No. 325 100

MAKITA 7.2 V Part No. 19 16 79-9

9.6 V Part No. 19 16 81-2

9.6 V Part No. 19 20 19-4

The optimum charging current is always

used depending on the temperature, volt-

age and internal resistance.

The two LED’s (1.9) indicate the respective

charging operation of the charger.

The right LED is the display for charging

chamber (1.1), the left LED for charging

chamber (1.2).

LED yellow - steady

= -Charger is ready for use.

LED green - ﬂ ashing

= -Battery pack being charged.

LED green - fast ﬂ ashing

= -Battery pack being charged at max.

charging current.

LED green - steady

= -Battery pack fully charged, conservation

charge on.

LED red - ﬂ ashing

= -General malfunction, e. g. incorrect po-

larity of battery pack, full contact not

being made, short-circuit, battery pack

faulty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool MCU 15 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info