Bedienungsanleitung Festool OF 1010 REQ (Seite 16 von 106) (Alle Sprachen)

796174

Zoom out

Zoom in

Vorherige Seite

1/106

Nächste Seite

– Do not clamp tools with an unsuitable

shank diameter in the clamping collet.

– Only use tools that meet standard

EN 847-1. All Festool routing tools fulfi l

these requirements.

– Ensure that the router bit is seated firmly

and that it runs perfectly.

– The clamping collet and locking nut must

not show any signs of damage

– Do not use cracked or deformed router

bits.

–

Wear suitable personal protective equip

ment: Ear protection, protective goggles,

dust mask for work that generates dust,

protective gloves for working with rough

materials and for changing tools.

–Only for AS/NZS: The tool shall always be

supplied via residual current device with a

rated residual current of 30 mA or less.

2.3 Sawing aluminium

When sawing aluminium, the following meas

ures must be taken for safety reasons:

– Install an upstream residual-current circuit

breaker (RCD, PRCD).

– Connect the power tool to a suitable dust

extractor with an antistatic suction hose.

– Regularly clean dust deposits from the mo

tor housing on the power tool.

– Wear protective goggles.

2.4 Emission levels

The levels determined in accordance

with EN 62841 are typically:

Sound pressure level LPA = 92 dB(A)

Sound power level LWA = 103 dB(A)

Uncertainty K = 3 dB

CAUTION

Noise generated when working

Risk of damage to hearing

► Use ear protection.

Vibration emission level ah (vector sum for

three directions) and uncertainty K measured in

accordance with EN 62841:

ah = 5.5 m/s2

K = 2 m/s2

The specified emission levels (vibration, noise)

– are used to compare machines.

– They are also used for making preliminary

estimates regarding vibration and noise

load during operation.

– They represent the primary applications of

the power tool.

CAUTION

The emission values may deviate from the

specified values. This is dependent on how

the tool is used and the type of workpiece

being machined.

► The actual load during the entire operating

cycle must be evaluated.

► Depending on the actual load, suitable pro

tective measures must be defined in order

to protect the operator.

3 Intended use

The router is designed for routing wood, plas

tics and wood-based materials.

If the cutters are used for the intended purpose

outlined in the Festool Sales, they may also be

used to machine aluminium and plasterboard.

This power tool may only be used by experts or

instructed persons.

The user is liable for improper or non-in

tended use.

4 Technical data

Router OF 1010 REBQ,

OF 1010 REQ

Power 1010 W

Speed 9500–23,000 rpm

Max. speed (no-load) 26,000 rpm

Quick depth adjust

ment 55 mm

Fine depth adjustment 8 mm

Drive shaft connecting

thread M16 x 1.5

Cutter diameter Max. 35 mm

Weight as per EPTA

procedure 01:2014: 3.1 kg

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool OF 1010 REQ Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info