Bedienungsanleitung Festool OF 1010 REQ (Seite 20 von 106) (Alle Sprachen)

796174

Zoom out

Zoom in

Vorherige Seite

1/106

Nächste Seite

that the underside of the router table is par

allel to the workpiece surface.

When working with marking-up lines, the

marks on the platen [7-1] and the scale on the

support [7-2] show the centre axis of the cutter.

For a more precise setting, a fine adjust

ment is available as an accessory for the

guide system.

8.4 Routing with the beam compasses

With the SZ-OF 1000 beam compasses (acces

sory) you can make circular cuts or segments

of circles with diameters from 153 to 760 mm.

► The beam compasses are pushed into the

front groove of the platen until the desired

radius is set.

► Lock the beam compasses with the rotating

knob [1-4].

To prevent the tip of the compasses

from making a hole in the workpiece,

fix a thin board at the centre point by

means of double-sided adhesive tape.

8.5 Copy cutting

A copying ring or the copying device is used to

exactly reproduce existing workpieces (acces

sories).

Copying ring

When choosing the size of the copying

ring [5-1], ensure that the cutter [5-2] being

used fits through its opening.

► Secure the copying ring to the router table

from below in place of the covering

ring [4-1].

Excess Y (figure [5]) of the workpiece to the

template is calculated as follows:

Y = (copying ring diameter - cutter diameter)/2

The copying ring can be exactly centred with the

ZD-OF centring mandrel (accessory).

Copying device

The copying device requires the angle arm WA-

OF [8-2] and the copier scanning set KT-OF,

consisting of a roller support [8-6] and three

copying rollers [8-7].

► Use the rotary knob [8-1] to tighten the an

gle arm to the required height on the threa

ded hole [8-3].

► Fit a copying roller to the roller support and

use the rotary knob [8-5] to tighten it on the

angle arm. Make sure that the copying roll

er and the router have the same diameter.

► The distance between the feeler roller and

the cutter axis can be adjusted by turning

the adjusting wheel [8-4].

8.6 Edge band trimming

Protruding edge bands can be flush trimmed

with the angle arm WA-OF [9-2] in connection

with the guide plate UP-OF [9-5] (accessory).

► Screw the angle arm into the platen’s

threaded bore [9-1] with the rotating

knob [9-3].

► Bolt the guide plate to the angle arm with

the rotating knob [9-4].

► Adjust the milling depth so that this is equal

to the thickness of the edge band + 2 mm.

► Move the guide plate [10-1] as close as

possible to the cutter by loosening the ro

tating knob [10-3].

► Adjust the depth of the guide plate with the

adjusting wheel [10-2] so that during trim

ming a few decimillimetres of the edge

band are left protruding which can then be

sanded down by hand.

9 Service and maintenance

WARNING

Risk of injury, electric shock

► Always pull the mains plug from the socket

before performing any servicing and main

tenance work.

► All maintenance and repair work which re

quires the housing to be opened should al

ways be carried out by an authorised serv

ice workshop.

Customer service and repairs must

only be carried out by the manufac

turer or service workshops. Find the

nearest address at:

www.festool.co.uk/service

Always use original Festool spare

parts. Order no. at:

www.festool.co.uk/service

EKAT

235

The tool is equipped with special self-discon

necting carbon brushes. If they wear out, the

power supply is disconnected automatically and

the tool stops.

Observe the following instructions:

► Damaged safety devices and components

must be repaired or replaced in a recog

nised specialist workshop, unless otherwise

indicated in the operating instructions.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool OF 1010 REQ Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info