Bedienungsanleitung Festool of 1400 ebq plus (Seite 14 von 86) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

426963

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

Vibration emission level (3-axis) a

= 3.5 m/s²

Uncertainty K = 2.0 m/s²

The emission values speciﬁ ed (vibration, noise)

were measured in accordance with the test con-

ditions stipulated in EN 60745 and are intended

for machine comparisons. They are also used for

making preliminary estimates regarding vibration

and noise loads during operation. The emission

values speciﬁ ed refer to the main applications for

which the power tool is used.

If the electric power tool is used for other ap-

plications, with other tools or is not maintained

sufﬁ ciently prior to operation, however, the vibra-

tion and noise load may be higher when the tool is

used. Take into account any machine idling times

and downtimes to estimate these values more

accurately for a speciﬁ ed time period. This may

signiﬁ cantly reduce the load during the machine

operating period.

4 Power supply and start-up

The line voltage and frequency must

correspond with the data on the ratings

plate!

Switch (1.13) serves as an On/Off switch (I = On/0

= Off). It may be latched with the locking knob on

the side (1.12) for continuous operation. Press-

ing the switch again releases the lock. See Fig.

2 for connection and disconnection of the power

cable.

5 Machine settings

Always remove the power supply plug

from the socket before carrying out any

work on the machine.

5.1 Electronics

Do not operate the tool if the electronics are faulty

as this can lead to the tool operating at excessive

speeds. If the start-up is not smooth or speed

adjustment is not possible, this indicates that the

electronics are faulty.

The OF 1400 EBQ, OF 1400 EQ features

full-wave electronics with the following

properties:

Smooth start-up

The smooth start-up ensures the router starts

up jolt-free.

Speed adjustment

You can regulate the speed steplessly between

10000 and 22000 min

-1

using the adjusting wheel

(1.10). This enables you to optimise the cutting

speed to suit the material:

Routing tool diameter

[mm]

Recommended

cutting material

Material

10 -25 25 - 40 40 - 60

Adjusting wheel setting

Hardwood 6 - 4 5 - 3 3 - 1

(HSS)

Softwood 6 - 5 6 - 3 4 - 1

HSS

(HW)

Chipboard,

coated

6 - 5 6 - 3 4 - 2 HW

Plastic 6 - 4 5 - 3 2 - 1 HW

Aluminium 3 - 1 2 - 1 1

HSS

(HW)

Plasterboard 2 - 1 1 1 HW

Constant speed

The pre-selected speed remains constant whether

the machine is in operation or in neutral position.

Temperature control

If the motor temperature becomes too high, the

power supply and speed are reduced. The tool

then only runs with reduced power to enable

rapid cooling by means of the motor ventilation.

After cooling down, the tool accelerates again

automatically.

Brake (OF 1400 EBQ)

The OF 1400 EBQ has an electronic brake which

brings the spindle with tool to a standstill within

approx. 2 seconds of the tool being switched off.

5.2 Changing tools

You can turn the machine upside down when

changing the tool.

a) Inserting the tool

- Insert the router into the open clamping collet as

far as possible, but at least up to the mark (

)

on the router shank. If the collet (3a.2) is not vis-

ible because it is blocked by the union nut (3a.3),

the milling tool (3a.1) must be inserted into the

collet at least far enough that the marker

longer overlaps with the union nut.

- Press the switch (1.14) for locking the spindle

on the right-hand side.

- Tighten the locking nut (1.15) with a 24 mm

open-end spanner.

Note: the spindle lock only blocks the motor spin-

dle in one direction of rotation at any one time.

Therefore when the nut is undone or tightened,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool of 1400 ebq plus Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info