Bedienungsanleitung Festool OF1400EB (Seite 16 von 82) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

574098

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

The machine must always be held with

both hands by the designated handles

(1.5, 1.11).

For work that generates dust, wear a dust

mask.

Always advance the router in the direction op-

posite to the direction of rotation of the cutter

(counter-routing)!

When routing (ensure feed direction of power tool

is the same as cutting direction of tool, Fig. 9).

6.1 Aluminium processing

When processing aluminium, the follow-

ing measures must be taken for safety

reasons:

- Pre-connect a residual current circuit-breaker

(FI, PRCD).

- Connect the machine to a suitable dust extractor.

- Clean tool regularly of dust accumulations in

the motor housing.

Wear protective goggles.

6.2 Freehand routing

Freehand routing is the method normally used for

lettering or shapes, and for routing edges using

cutters with a guide pin or ring.

6.3 Routing with the parallel guide

The parallel guide (4.2) supplied can be used for

routing parallel to the edge of the workpiece.

- Secure both guide rods (4.2) with the two rotary

knobs (4.4) on the side stop.

- Insert the guide rods into the grooves on the

router base to the required distance and secure

them by turning the rotary knob (4.5).

- Fine adjustment: Unscrew the rotary knob (4.6)

to make ﬁ ne adjustments with the adjusting

wheel (4.8). The scale ring (4.7) has a 0.1 mm

scale for this purpose. If the adjusting wheel is

held secure, the scale ring can be turned sepa-

rately and set to „Zero“. The millimetre scale

(4.1) on the main casing is useful when making

larger adjustments. Tighten the rotary knob (4.6)

again on completion of any ﬁ ne adjustments.

- Adjust both guidance jaws (4.3, 5.1) so that they

are approx. 5 mm from the router. To do this,

undo screws (5.2) and tighten again after com-

pleting the adjustments.

- As shown in Fig. 5, slide the extractor hood (5.4)

from behind until it latches into place on the side

stop. You can connect an extractor hose with a

diameter of 27 mm or 36 mm to the extractor

connector (5.3).

6.4 Routing with the FS guide system

The guide system, available as an accessory, fa-

cilitates routing straight grooves.

- Fasten the guide stop (6.1) to the platen with the

guide rails of the parallel guide.

- Fasten the guide rail (6.3) with FSZ screw clamps

(6.4) to the workpiece. Make sure that the safety

distance X (Fig. 6) of 5 mm between the front

edge of the guide rail and cutter or groove is

observed.

- Place the guide stop onto the guide rail as shown

in Fig. 6. To ensure a backlash-free guidance of the

router stop you can adjust two guide cheeks with

a screwdriver through the side openings (6.2).

- Screw the height-adjustable support (6.6) of the

router table’s threaded bore in such a way that

the underside of the router table is parallel to

the surface of the workpiece.

When working with marking-up lines, the marks

on the platen (6.5) and the scale on the support

(6.6) show the centre axis of the cutter.

Fine adjustment

Distance X can be adjusted precisely with the ﬁ ne

adjuster (7.5, Accessory).

- Fit the ﬁ ne adjuster (7.5) between the tool and

the guide stop on the guide rails.

- Insert the adjusting wheel (7.2) into the guide

stop as shown in Fig. 7.

- Screw the adjusting wheel (7.2) into the nut on

the ﬁ ne adjuster.

- To adjust distance X, unscrew the rotary knob

(7.1) on the guide stop and tighten the rotary

knob (7.3) on the ﬁ ne adjuster.

- Adjust to the required distance X by turning the

adjusting wheel (7.2), and then tighten the rotary

knob (7.1) on the guide stop.

6.5 Copy cutting

A copying ring or the copying device is used to

exactly reproduce existing workpieces (both avail-

able as accessories).

a) Copying ring

When choosing the size of the copying ring make

sure that the cutter used ﬁ ts through the ring’s

opening.

The distance Y (Fig. 9) between the workpiece and

template is calculated by

Y = (Ø copying ring - Ø cutter)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool OF1400EB Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info