Bedienungsanleitung Festool PDC 18.4 (Seite 14 von 89) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

574923

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

PDC 18/4

6.4 Light and battery capacity indicator

The LED on the lamp

[1-2]

is both a light and

a battery capacity indicator

Press the LED light switch

[1-1]

1x ... LED, working area illumination

2x ... capacity indicator, indicates the charging

state of the battery pack (not with NiCd and

NiMH battery packs)

7Settings

7.1 Changing direction of rotation [1-9]

• Switch to the left = clockwise rotation

• Switch to the right = counterclockwise rotation

7.2 Changing gear

You can change gear using the gear switch

[1-7]

7.3 Adjusting the torque[1-8]

Fastening

Select the correct torque setting:

Position 1 = low torque

Position 12 = high torque

acoustic signal

sounds when the preset torque

is reached and the machine then switches off. You

must release and press the ON/OFF switch

[1-4]

again to start the machine.

Drilling

Mark is aligned with drill symbol = maximum

torque.

7.4 Impact drilling

The machine was designed for impact drilling

into tiles, masonry and stone.

Set the selector switch

[1-6]

to the hammer sym-

bol. Set the adjusting wheel

[1-8]

to the drill sym-

bol.

8 Tool holder, attachments

Prior to initial use:

apply multi-purpose grease

to the drill spindle and gearbox neck.

8.1 CENTROTEC tool chuck [6]

Quick change of tools with CENTROTEC shaft

Only clamp CENTROTEC tools in CENTRO-

TEC tool chucks.

Wear gloves when replacing!

8.2 Chuck [7]

For clamping drill bits and bits with max. shaft di-

ameter of 13 mm.

Clamp tool centrally in the chuck.

8.3 Angle attachment [8]

Drilling and screwdriving at right angle to machine

(partly as an accessory).

8.4 Tool holder in the drill spindle [9]

Bits can be inserted directly into the hexagon sock-

et holder of the drill spindle.

8.5 Depth stop [10]

The depth stop (partly as an accessory) allows the

user to insert screws to a predefined depth. You can

set the dimension by which the screw head pro-

trudes above or is recessed below the surface of the

workpiece.

Depth setting

Turn the housing

[10-1]

to set

the desired fastening depth.

Each detent position changes the

fastening depth by 0.1 mm.

Sleeve A/B must be removed before a screw can be

unscrewed.

LED green – lit continuously:

charged > 60 %

LED green – flashing slowly:

charged 30 % – 60 %

LED green – flashing quickly:

charged 0 % – 30 %

LED yellow – lit continuously:

battery is empty

LED red – lit continuously:

bat-

tery temperature is outside the

permitted range.

LED red – flashing:

indicates a

general fault, e.g. incomplete

contact, short circuit, battery

pack faulty, etc.

WARNING

Risk of injury

Always switch off the machine before adjusting

settings!

WARNING

Risk of injury, electric shock

Always disconnect the battery pack before any

type of work on the machine!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PDC 18.4 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info