Bedienungsanleitung Festool PRECISIO CS 50 EBG - 2021 (Seite 21 von 180) (Alle Sprachen)

778609

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

4 Safety instructions

4.1 General safety instructions

WARNING! Read all safety warn-

ings, instructions, illustrations and

specifications provided with this power tool.

Failure to follow all instructions listed below may

result in electric shock, ﬁre and/or serious injury.

Keep all safety information and instructions for

future reference.

The term “power tool” used in the safety instruc-

tions refers to mains-powered power tools (with

power cable) or battery-powered power tools

(without power cable).

4.2 Safety instructions for table saws

Guarding related warnings

a. Keep guards in place. Guards must be in

working order and be properly mounted. A

guard that is loose, damaged, or is not func-

tioning correctly must be repaired or replaced.

b. Always use saw blade guard and riving knife

for every through–cutting operation. For

through-cutting operations where the saw

blade cuts completely through the thickness

of the workpiece, the guard and other safety

devices help reduce the risk of injury.

c. Immediately reattach the guarding system af-

ter completing an operation (such as rabbet-

ing, dadoing or resawing cuts) which requires

removal of the guard and/or riving knife. The

guard, riving knife, and anti-kickback device

help to reduce the risk of injury.

d. Make sure the saw blade is not contacting the

guard, riving knife or the workpiece before

the switch is turned on. Inadvertent contact

of these items with the saw blade could cause

a hazardous condition.

e. Adjust the riving knife as described in this

instruction manual. Incorrect spacing, po-

sitioning and alignment can make the riving

knife ineffective in reducing the likelihood of

kickback.

f. For the riving knife to work, it must be en-

gaged in the workpiece. The riving knife is

ineffective when cutting workpieces that are

too short to be engaged with the riving knife.

Under these conditions a kickback cannot be

prevented by the riving knife.

g. Use the appropriate saw blade for the riving

knife. For the riving knife to function properly,

the saw blade diameter must match the ap-

propriate riving knife and the body of the saw

blade must be thinner than the thickness of

the riving knife and the cutting width of the

saw blade must be wider than the thickness

of the riving knife.

Cutting procedures warnings

a. DANGER: Never place your ﬁngers or

hands in the vicinity or in line with the

saw blade. A moment of inattention or

a slip could direct your hand towards the

saw blade and result in serious personal inju-

ry.

b. Feed the workpiece into the saw blade or

cutter only against the direction of rotation.

Feeding the workpiece in the same direction

that the saw blade is rotating above the table

may result in the workpiece, and your hand,

being pulled into the saw blade.

c. Never use the mitre gauge to feed the work-

piece when ripping and do not use the rip

fence as a length stop when cross cutting with

the mitre gauge. Guiding the workpiece with

the rip fence and the mitre gauge at the same

time increases the likelihood of saw blade

binding and kickback.

d. When ripping, always apply the workpiece

feeding force between the fence and the saw

blade. Use a push stick when the distance

between the fence and the saw blade is less

than 150 mm, and use a push block when this

distance is less than 50 mm. “Work helping”

devices will keep your hand at a safe distance

from the saw blade.

e. Use only the push stick provided by the man-

ufacturer or constructed in accordance with

the instructions. This push stick provides suf-

ﬁcient distance of the hand from the saw blade.

f. Never use a damaged or cut push stick. A

damaged push stick may break causing your

hand to slip into the saw blade.

g. Do not perform any operation “freehand”.

Always use either the rip fence or the mitre

gauge to position and guide the workpiece.

“Freehand” means using your hands to sup-

port or guide the workpiece, in lieu of a rip

fence or mitre gauge. Freehand sawing leads

to misalignment, binding and kickback.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PRECISIO CS 50 EBG - 2021 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info