Bedienungsanleitung Festool PRECISIO CS 50 EG - 2021 (Seite 30 von 180) (Alle Sprachen)

778610

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

8.3 Push stick

- When not in use, the push stick [2-4] should be

placed in the accessory holder [2-1].

9 Service and maintenance

Always pull the mains plug before main-

taining, servicing or making any kind of

adjustment.

All maintenance and repair work which

requires the motor housing to be opened

must only be carried out by an authorised

service workshop.

Damaged safety devices and components

must be repaired or replaced in a recog-

nised specialist workshop in accordance

with regulations, unless otherwise indi-

cated in the operating manual.

Customer service and repairs: Only by

manufacturer or service workshops. Find

the nearest address at:

www.festool.co.uk/service

EKAT

235

Always use original Festool spare parts.

Order no. at:

www.festool.co.uk/service

The machine is equipped with special self-dis-

connecting carbon brushes. If they wear out, the

power supply is disconnected automatically and

the tool stops.

Maintain your machine regularly to make sure it

functions properly:

- Use an extractor to remove dust deposits,

- Keep guide rods [1-10] clean and grease them

regularly,

- Replace worn or damaged table inserts,

- Use the slide [11-1] to open the ﬂap [11-3] in

order to remove offcuts from the lower guard.

To remove larger deposits, the ﬂap can be com-

pletely opened by unscrewing the screw [11-2].

Close the ﬂap again prior to use.

- After completing work, wind up the power cable

onto the accessory holder [2-1].

- A damper allows the saw unit to retract evenly

along the entire cutting length. If this is not the

case, the damper can be adjusted using the

hole [2-5].

- If it becomes necessary to replace the power

cable, this must be carried out by the manufac-

turer or the service team in order to ensure that

no hazards arise.

10 Accessories, tools

Festool provides comprehensive accessories

which allow you to use your machine effectively

and for diverse applications, e.g.: Extension ta-

bles (width and length), sliding table, trimming

attachment, dust extraction set.

In order to be able to saw different materials

quickly and cleanly, Festool offers saw blades that

are specially designed for your machine.

The order numbers of the accessories and tools

can be found in the Festool catalogue or on the

Internet under “www.festool.com”.

11 Disposal

Do not throw the power tool out in your house-

hold waste. Dispose of machines, accessories

and packaging at an environmentally responsi-

ble recycling centre. Observe the valid national

regulations.

EU only: In accordance with European Directive

2002/96/EC on waste electrical and electronic

equipment and implementation in national law,

used power tools must be collected separately

and handed in for environmentally friendly recy-

cling.

Information on REACh: www.festool.com/

reach.

Imported into the UK by

Festool UK Ltd

1 Anglo Saxon Way

Bury St Edmunds

IP30 9XH

Great Britain

General information

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PRECISIO CS 50 EG - 2021 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info