Bedienungsanleitung Festool PRECISIO CS 70 EG - 2020 (Seite 26 von 196) (Alle Sprachen)

778612

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

6 Set-up, operation

WARNING

Risk of accident if the machine is operated us-

ing the incorrect voltage or frequency.

fThe line voltage and frequency of the power

supply must match those speciﬁed on the

machine's rating plate.

fOnly Festool machines with a rated voltage of

120 Volt may be used in North America.

fBefore use always inspect the ﬂexible lead

and the plug. Have the defects repaired by a

specialist repair shop.

fOutside the premise use only approved ex-

tension leads and cable connections.

6.1 Setting up the machine

Ensure that the ﬂoor around the machine is lev-

el, in good condition and free of loose objects

(e.g. chips and offcuts).

LThe machine can be set up with or without

the legs unfolded.

fTo unfold the legs: Loosen the four rotary

knobs [1-11] all the way.

fUnfold the legs [1-1] and tighten the rotary

knobs [1-11] again.

If the machine wobbles, the length of one leg can

be adjusted by turning the end cap [1-12] until

the machine stands securely.

6.2 Prior to initial operation

6.2a Fitting the knob

fScrew the supplied rotary knob [2-6] anti-

clockwise into the guide rod.

6.2b Installing the guard (ﬁg. 12)

fRemove the yellow safety sticker [12-4].

fSet the saw to maximum cutting depth and the

mitre to 0°.

fPull the riving knife [12-1] into the upper po-

sition.

f1 Take hold of the guard [12-3] and com-

pletely unscrew the screw [12-2].

f2 Place the guard [12-3] on the riving

knife [12-1]. In doing this, guide the length-

wise pin that is located in the guard [12-3] into

the groove [12-6] on the riving knife [12-1]

and push the screw [12-2] into the hole [12-5]

in the riving knife [12-1] and tighten it.

f3 Tighten the screw [12-2].

5.4 Emission levels

Typically, the noise levels that are determined in

accordance with EN 62841 (see EC declaration of

conformity) are as follows:

Sound pressure level LPA = 84 dB(A)

Sound power level LWA = 98 dB(A)

Measuring uncertainty allowance K = 3 dB

CAUTION

The noise produced during work may damage

your hearing.

fWear ear protection!

- The speciﬁed noise emission levels have been

measured in accordance with the standard test-

ing method and can be used to compare tools.

- The speciﬁed noise emissions can also be used

for making preliminary estimates regarding

noise load.

CAUTION

The noise emissions during actual use of the

power tool can differ from the declared val-

ues depending on the ways in which the tool

is used especially what kind of workpiece is

processed.

fIdentify safety measures to protect the oper-

ator that are based on an estimation of ex-

posure in the actual conditions of use (tak-

ing account of all parts of the operating cycle

such as the times when the tool is switched

off and when it is running idle in addition to

the trigger time).

5.5 Other risks

In spite of compliance with all relevant design

regulations, dangers may still present them-

selves when the machine is operated, e.g.:

- Workpiece parts being thrown off,

- Parts of damaged tools being thrown off,

- Noise emissions,

- Wood dust emissions.

P R E C I S I O - GB

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PRECISIO CS 70 EG - 2020 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info