Bedienungsanleitung Festool PRECISIO CS 70 EG - 2020 (Seite 31 von 196) (Alle Sprachen)

778612

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

P R E C I S I O - GB

fUse the preset proﬁle setting rail as a length-

wise ruler (ﬁg. 1) to guide the workpiece.

fYou can adjust the cutting width using the

scales.

fGuide the workpiece by hand, keeping your

arms away from the saw blade’s centre line.

fUse the push stick [11-2] to guide the work-

piece accurately past the saw blade.

fPlace the push stick in the accessory hold-

er [11-4] when not in use.

9.1b Angled cuts

The mitre angle of the saw blade needs to be

adjusted for angled cuts, see section 8.7.

9.1c Non-through cuts

If the guard has been removed, the riving knife

can be adjusted by ﬁrmly pulling by two locking

positions. The riving knife is used in the upper

locking position for all applications, except for

non-through cuts.

Before starting work

fRemove the upper guard [6-4].

fMove the riving knife [6-1] into the lower lock-

ing position by pushing it down ﬁrmly.

Creating non-through cuts

When executing non-through cuts, pay particular

attention that the tool is guided precisely. To do

this, push the workpiece down ﬁrmly onto the

table. Select the cutting sequence so that the

workpiece side already sawed out is not the fence

side (risk of kickback).

Rabbeting

fSet the cutting depth and fence of the ﬁrst side

of the rebate.

fCarry out the ﬁrst saw cut of the rebate by

guiding the workpiece by hand. Keep your

arms away from the saw blade’s centre line.

fUse the push stick [11-2] to guide the work-

piece past the saw blade.

fTurn the workpiece.

fSet the cutting depth and fence of the second

side of the rebate.

fMake the second saw cut of the rebate.

fUse the push stick [11-2] to guide the work-

piece past the saw blade.

Rabbeting on workpieces ≤ 12 mm with a table

saw with sliding function (with the saw blade

locked)

fUse the fence as a cross-cutting fence (ﬁg. 3).

fObserve the operating instruction for cross

cuts (see section 9.2a).

NEVER use the fence as a rip fence when

rabbeting on the short side.

Grooving

fAdjust the cutting depth on the saw blade.

fUse the fence as a guide.

fGuide the workpiece by hand. Keep your arms

away from the saw blade‘s centre line.

fUse the push stick [11-2] to guide the work-

piece past the saw blade.

fRepeat the process until the required grooving

depth is achieved.

After ﬁnishing work

fAfter executing the non-through cuts, move

the riving knife [6-1] back into the upper posi-

tion and attach the guard [6-4].

Complicated concealed cut process

fe.g. plunge saws, resawing, dadoing, proﬁle

routing and ﬂuting are not permitted.

9.1d Featherboard

NOTE

Use a featherboard for non-through cuts. Fit the

featherboard on the fence and the table so that the

featherboard pushes the workpiece down ﬁrmly

onto the plate during cutting. Featherboards are

not included with the delivery.

9.1e Longitudinal cuts at an angle

fOnly use the left fence when making longitu-

dinal cuts at an angle in material with an edge

length of ≤ 150 mm. This creates more space

between the fence and the saw blade.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PRECISIO CS 70 EG - 2020 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info