Bedienungsanleitung Festool PS400EBQ (Seite 16 von 110) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

573107

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

CARVEX

The emission values specified (vibration,

noise) were measured in accordance with the

test conditions stipulated in EN 60745 and are

intended for machine comparisons. They are

also used for making preliminary estimates re-

garding vibration and noise loads during oper-

ation.

The emission values specified refer to the

main applications for which the power tool is

used. If the electric power tool is used for oth-

er applications, with other tools or is not main-

tained sufficiently prior to operation, however,

the vibration and noise load may be higher

when the tool is used. Take into account any

machine idling times and downtimes to esti-

mate these values more accurately for a spec-

ified time period. This may significantly reduce

the load during the machine operating period.

6Operation

Connecting and detaching the mains power

cable [1-7] see Fig. [2].

Insert the plug into a socket.

The electric power tool has one button [1-2]

on each side for switching on/off.

The PSB 400 EBQ also has a variable speed

trigger [1-3] with switch lock [1-4]. For con-

tinuous operation, use the button [1-2].

7 Settings

7.1 Changing tools

Selecting saw blade

Only use saw blades with a T-shank. The

saw blade should not be longer than

that required for the intended cut. To

ensure safe guidance, during the cut the saw

blade should emerge at the bottom of the

workpiece at every point.

Only use cross-set saw blades when using

the angle and adapter table. We recom-

mend Festool saw blade S 105/4 FSG.

Inserting saw blade

Always pull the mains plug out of the

socket before changing blades.

If necessary, push the chip guard [3-1] up-

wards.

Push the saw blade [3-4] into the opening

as far as the stop with its teeth in cutting

direction [3-2].

Turn the saw blade [3-4] approx. 30° clock-

wise until it engages.

The guidance jaws adjust automatically to the

saw blade used.

Check that the saw blade is secure. A

loose saw blade can fall out and cause

an injury.

In the case of very short saw blades, it is

advisable to remove the saw table (see

chapter

7.4

) before inserting the saw

blade.

PS 400 EBQ PSB 400 EBQ

Sawing wood

Handle a

=6,0 m/s

=10,0 m/s

K = 2,0 m/s

Gear

head

=11,0 m/s

K = 2,0 m/s

Sawing metal

Handle a

=7,0 m/s

=11,0 m/s

K = 2,0 m/s

Gear

head

=12,0 m/s

K = 2,0 m/s

WARNING

Unauthorised voltage or frequency!

Risk of accident

The mains voltage and the frequency of

the power source must correspond with

the specifications on the machine's name

plate.

In North America, only Festool machines

with the voltage specifications 120 V/60

Hz may be used.

WARNING

Risk of injury, electric shock

Always pull the plug out of the socket be-

fore performing any type of work on the

machine!

CAUTION

Hot and sharp tools

Risk of injury

Wear protective gloves!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PS400EBQ Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info