Bedienungsanleitung Festool PSB 420 EBQ (Seite 15 von 99) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510170

Zoom out

Zoom in

Vorherige Seite

1/99

Nächste Seite

C A R V E X

Increase possible for other applications, with other

insertion tools or if not maintained adequately. Take

note of idling and downtimes of machine!

6Operation

Connecting and detaching the mains power cable

[1-7]

see Fig.

[2]



Insert the plug into a socket.

The electric power tool has one button

[1-2]

each side for switching on/off.

The PSB 420 EBQ also has a variable speed trigger

[1-3]

with switch lock

[1-4]

. For continuous opera-

tion, use the button

[1-2]

7 Settings

7.1 Changing tools

Selecting saw blade

Only use saw blades with a T-shank. The

saw blade should not be longer than that re-

quired for the intended cut. To ensure safe

guidance, during the cut the saw blade should

emerge at the bottom of the workpiece at every

point.



Only use cross-set saw blades when using the

angle and adapter table. We recommend Fes-

tool saw blade S 105/4 FSG.

Inserting saw blade

Always pull the mains plug out of the socket

before changing blades.



If necessary, lift up the chip guard

[3-1]



Slide the saw blade

[3-4]

into the opening

[3-2]

as far as the stop with its teeth in the cutting di-

rection.



Turn the saw blade

[3-4]

clockwise approx. 30°.

Check that the saw blade is secure. A loose

saw blade can fall out and cause an injury.



If the saw blade is very small, it is advis-

able to remove the saw base (see chapter 7.4)

before inserting the saw blade.

Adjust the saw blade guide after every saw blade

change:

The saw blade guide was designed to improve guid-

ance of the saw blade.



Remove the saw base (see chapter 7.4).



Tighten the screw

[3-6]

using the Allen key

[3-

until the jaws are

almost

touching the saw

blade.

Ejecting saw blade



When ejecting the saw blade, hold the electric

power tool such that no persons or animals can

be injured.



Push the saw blade ejection

[3-3]

forwards as

far as the stop.



A tool change is only possible when the tool

holder is located in the upper position!

If the saw blade is stuck and cannot be changed:

Operate the jigsaw at high speed for 3 - 10 seconds.

Actuate the saw blade ejection

[3-3]

again.

7.2 Using the chip guard

The chip guard

[3-1]

prevents chips flying away and

improves the efficiency of the chip extraction sys-

tem.



Using minimal pressure, push the chip guard

[3-1]

downwards.

7.3 Inserting the splinterguard

The splinterguard prevents the edges of the mate-

rial from splintering during the cut, even at the end

where the saw blade exits the material.



Switch off the machine and slide the splinter-

guard

[4-1]

into the guide

[4-2]

and up to the

WARNING

Unauthorised voltage or frequency!

Risk of accident



The mains voltage and the frequency of the pow-

er source must correspond with the specifica-

tions on the machine's name plate.



In North America, only Festool machines with

the voltage specifications 120 V/60 Hz may be

used.

WARNING

Risk of injury, electric shock



Always pull the mains plug out of the socket be-

fore performing any type of work on the ma-

chine!

CAUTION

Hot and sharp tools

Risk of injury



Wear protective gloves.

NOTE

Damage to the machine or saw blade



Do not tighten the screw [3-6] too firmly! It must

be possible to move the saw blade slightly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PSB 420 EBQ Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info