Bedienungsanleitung Festool PSC 420 Li 18 (Seite 19 von 132) (Alle Sprachen)

778632

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

► Switch on the jigsaw.

► On a level surface, slide in the splinterguard

(not using your hand!) while the machine is

operating until it is flush with the front edge

of the saw table (speed setting 5). This cuts

into the splinterguard.

When it is worn, push the splinterguard

approx. 3 mm further to the rear and con

tinue using it.

To guarantee reliable operation of the

splinterguard, it must seal tightly on both

sides of the saw blade. A new splinter

guard should therefore be fitted after ev

ery saw blade change to guarantee splint

er-free cuts.

8.4 Changing the saw table

► Open the change lever [1-9].

► Remove the saw table downwards.

Assembly is performed in reverse se

quence to removal. Ensure that the saw

table is firmly seated in the guide.

Instead of the saw table, the WT-PS 400 angle

table or ADT-PS 400 base adapter can be instal

led at the support.

Never saw without the saw table, or one

of the other tables or adapters offered in

the Festool accessories range.

8.5 Extraction

WARNING

Health risk due to dust

► Always work with an extractor.

► Comply with national regulations.

The extraction adapter [5-3] allows jigsaws to

be connected to a dust extractor (hose diameter

27 mm).

► Insert the extraction adapter in the rear

opening of the saw table so that the

hook [5-2] engages in the recess [5-1].

► To remove the extraction adapter, press the

hook [5-2].

Due to the low power consumption of the

machine (low energy consumption), dust

extractors with an automatic switch-on

function will sometimes only start up when

the actual cut is made.

► Set the dust extractor to continuous opera

tion for special applications (e.g. low stroke

rate, soft wood).

8.6 Adjusting the pendulum stroke

In order to saw different materials with the

proper rate of advance the pendulum stroke

can be adjusted. Set the required stroke via the

pendulum stroke switch [1-12]:

Position 0 = pendulum stroke disabled

Position 3 = maximum pendulum stroke

Recommended pendulum stroke setting

Softwood, chip board, wood fibreboard 1 - 3

Blockboard, plywood, plastic 1 - 2

Ceramics 0

Aluminium, non-ferrous metals 0 - 2

Steel, hardwood 0 - 1

8.7 Stroke rate control

Using the adjusting wheel [1-6], the stroke rate

can be continuously adjusted between 1500 and

3800 rpm (PSBC 420 EB: 1000–3800 rpm). This

enables you to optimise the cutting speed to

suit the respective material.

Automatic load detection is activated in posi

tion A: The stroke rate drops when idling and is

adjusted to the highest setting when the work

piece is introduced.

Recommended stroke rate (position of the ad

justing wheel)

Hard and soft wood, blockboard, ply

wood, chipboard A

Fibreboard 4–A

Plastic 3–A

Ceramic, aluminium, non-ferrous met

als 3–5

Steel 2–4

9 Working with the electric

power tool

CAUTION

Materials which produce a lot of dust

Damage to the machine due to the ingress of

dust, risk of injury

► Do not work overhead.

When working on small or thin workpieces, al

ways use a stable base, or the CMS module (ac

cessory).

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PSC 420 Li 18 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info