Bedienungsanleitung Festool ras 115 04e set (Seite 6 von 20) (Englisch, Französisch, Spanisch)

389659

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Attaching the abrasive

Stickﬁ x is a hook-and-loop fastening sys-

tem. Stickﬁ x sanding pads allow the use

of self-adhesive hook-and-loop abrasives

such as Stickﬁ x sandpapers and sanding

cloths.

Simply press the abrasive onto the sanding pad

and pull it off again after use.

Use only abrasives with an undam-

aged Stickﬁ x hook-and-loop coating. Before use,

check that the coating has not been damaged by

improper use (such as over heating).

The Mini-Stickﬁ x D 52 sanding pad

was developed for use in conﬁ ned spaces and

with small areas. This small-diameter pad and

the afﬁ xed abrasive will inevitably heat up in use

more than larger pads, since the same pressure

is distributed over a smaller area. Sand only with

moderate pressure and do not sand continuously

for too long. Lift the sander off the workpiece at

intervals to allow friction heat to dissi-pate.

Working with the tool

Always secure the workpiece in

such a manner that it cannot move while being

sanded.

Never overload the tool by using

too much pressure! The best sanding results

are achieved when applying moderate pressure.

Sanding performance and quality depend primarily

on the choice of the right abrasive.

For safe guidance, always hold the

tool with both hands.

We recommend the following settings on the ro-

tary control (2.1) for electronic machines:

• Sanding hard GRP components (limited suit-

ability).

3 - 6

• Sanding off dry, cracked paint.

• Stripping anti-fouling paints.

• Sanding wood.

2 - 4

• Sanding paint/varnish with tendency to smear

• Light sanding of thin top coats of paint.

• Cleaning sandstone, concrete, formwork materi-

als.

1 - 2

• Sanding thermoplastic materials.

• Smoothing treated woods with sanding brush.

Maintenance and care

All maintenance or repair work re-

quiring the motor housing to be opened must be

carried out only by an authorized service work-

shop. Maintenance or repair work carried out by

an unauthorized person can lead to the incorrect

connection of the wiring or other components,

which in turn can lead to accidents with serious

consequences.

Always remove the plug from the

mains supply socket before carrying out any work

on the machine!

Always keep the tool and in particular the ventila-

tion slots clean.

The tool is ﬁ tted with special motor brushes with

an automatic cut-out. When the brushes become

worn the power supply is shut off automatically

and the tool comes to a standstill.

Accessories, tools

For safety reasons, only use original

Festool accessories and tools!

The accessory and tool order number can be found

in the Festool catalog or on the Internet under

www.festool-usa.com.

Systainer

Many Festool products are shipped in a unique

system container, called "Systainer". This provides

protection and storage for the tool and acces-

sories. The Systainers are stackable and can be

interlocked together. They also can be interlocked

atop Festool CT dust extractors.

8.1

8.2

8.3

– Place one systainer on top of the other.

– Release all four latches on the lower systainer

by pulling back at their top edges (8.1).

– Slide all four latches upward (8.2).

– Snap all four latches back to their ﬂ at position

(8.3) so they engage the stacking tabs of the

upper systainer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool ras 115 04e set Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info