Bedienungsanleitung Festool rs 200 q (Seite 11 von 62) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

390250

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

the power tool is used.

If the electric power tool is used for other ap-

plications, with other tools or is not maintained

sufﬁ ciently prior to operation, however, the vibra-

tion and noise load may be higher when the tool is

used. Take into account any machine idling times

and downtimes to estimate these values more

accurately for a speciﬁ ed time period. This may

signiﬁ cantly reduce the load during the machine

operating period.

3 Power supply and start-up

The mains voltage must correspond to

the speciﬁ cation on the rating plate.

Switch (1.1) serves as an On/Off switch (I = On / 0

= Off). It may be latched with the locking knob on

the side (1.3) for continuous operation. Pressing

the switch again releases the lock.

Always switch the machine off before

connecting or disconnecting the mains

lead!

See Fig. 3 for connection and disconnection of the

power cable.

4 Electronics

The RS 200 EQ has an electronic control

with which the rotational speed can be

varied step-free.

This allows the sanding speed to be adapted to

the optimum level according to the material con-

cerned (see Chapter 6).

The speed is set using the rotary control button

(1.2).

5 Machine settings

Always remove the power supply plug

from the socket before carrying out any

work on the machine.

5.1 Dust extraction

Always connect the machine to a dust

extractor. Dust extractors prevent large

accumulations of dust in the air in the

working environment and dirt collecting

at the workplace.

Sanding dust is extracted through the extraction

channels in the sanding pad directly to the mate-

rial removal point.

a) Inboard extraction

The machines are ﬁ tted with inboard extraction as

standard. The sanding dust is extracted through

suction openings in the sanding base (2.3) and

trapped in the turbo-ﬁ lter (1.6). The turbo-ﬁ lter

has to be changed when it is so full of dust that

the extraction power diminishes.

Inserting a turbo-ﬁ lter

- Push the front cardboard section of the turbo-

ﬁ lter with the sealing lip (1.5) onto the extraction

nozzle (1.9) of the ﬁ lter holder

- Insert rear cardboard section with slot (1.7) onto

the retaining strip (1.8) of the ﬁ lter holder

- Push the ﬁ lter holder with its opening (1.10) as

far as it will go onto the extraction nozzle (1.11)

of the machine and clamp tight by turning rotary

knob (1.4).

b) External extraction by an extraction

unit

In order to avoid frequent changing of the turbo-

ﬁ lter when carrying longer sanding jobs, it is

possible to connect a Festool extractor to the unit

instead of using inboard extraction. In this case,

the extraction pipe (Ø 27 mm) of the extraction unit

is connected to the suction nozzle (1.11).

5.2 Sanding pad

The standard Stickﬁ x sanding pad for Stickﬁ x

abrasives can be replaced with a sanding pad for

clamping abrasives. Unscrew the six screws (2.1)

to do this.

Both sanding pads (with and without Stickﬁ x coat-

ing) are also available with a side edge protector

to prevent the sanding base from degrading pre-

maturely when sanding corners.

5.3 Attaching sanding material

Always use original Festool sanding ma-

terials!

Stickﬁ x abrasives

The appropriate Stickﬁ x sanding paper

and Stickﬁ x sanding felt can be fastened

quickly and easily onto the Stickﬁ x sand-

ing pad.

The self-adhesive sanding material is simply

pressed onto the sanding base and held safely

in place by the Stickﬁ x sanding base velcro sur-

face.

After use, the StickFix sandpaper is simply pulled

off.

Abrasives to clamp

Festool offers perforated abrasives to

clamp.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool rs 200 q Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info