Bedienungsanleitung Festool SYM 70 RE (Seite 18 von 130) (Alle Sprachen)

778608

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

2.4 Further safety instructions

–Only use saw blades that correspond to

the specifications for intended use. Saw

blades that do not fit correctly with the as

sembly parts will run unevenly and may

cause fragments to break off from the ma

terial and be ejected. These fragments may

hit the eyes of the user or any persons

standing in the vicinity.

–Only use saw blades with a chip angle ≤ 0°.

A chip angle > 0° will pull the saw into the

workpiece. There is a risk of injury caused

by saw kickback and the rotating work

piece.

– The power tool should only be used indoors

and in a dry environment.

–Before each use, check that the pendulum

guard is working correctly. Only use this

power tool when it is in perfect working or

der.

–Never reach into the chip ejector with your

hands. Rotating parts may injure your

hands.

–Dust that is harmful to your health may be

produced as you work (e.g. paint products

containing lead and some types of wood).

Contact with or inhalation of this dust may

pose a risk for the operating personnel or

persons in the vicinity. Observe the safety

regulations that apply in your country.

–Wear a P2 respiratory mask to protect

your health. In enclosed spaces, ensure

that there is sufficient ventilation and con

nect a mobile dust extractor.

– Replace any sawn-off or damaged limit

stops. Damaged limit stops may be ejected

when you work with the saw. Any persons

standing in the vicinity of the saw may be

injured.

–Only use original Festool accessories and

consumables. Only accessories tested and

approved by Festool are safe and perfectly

adapted to the machine and application.

–Only for AS/NZS: The tool shall always be

supplied via residual current device with a

rated residual current of 30 mA or less.

2.5 Aluminium processing

When sawing aluminium, the following

measures must be taken for safety reasons:

– Install an upstream residual-current circuit

breaker (RCD, PRCD).

– Connect the power tool to a suitable dust

extractor.

– Regularly clean dust deposits from the mo

tor housing on the power tool.

– Use an aluminium saw blade.

Wear protective goggles.

2.6 Other risks

In spite of compliance with all relevant design

regulations, dangers may still present them

selves when the machine is operated, e.g.:

– Touching rotating parts from the side: Saw

blade, clamping flange, flange screw,

– Touching live parts when the housing is

open and the mains plug is still plugged in,

– Workpiece parts being thrown off,

– Parts of damaged tools being thrown off,

– Noise emissions,

– Dust emissions.

2.7 Emission levels

Levels determined in accordance with EN 62841

are typically:

Sound pressure level LPA = 97 dB(A)

Sound power level LWA = 104 dB(A)

Uncertainty K = 3 dB

CAUTION

Noise generated when working

Risk of damage to hearing

► Use ear protection.

The declared noise emission values

– have been measured in accordance with a

standard test method and may be used for

comparing one tool with another,

– may also be used in a preliminary assess

ment of exposure.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool SYM 70 RE Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info