Bedienungsanleitung Festool SYM70E (Seite 13 von 79) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

573126

Zoom out

Zoom in

Vorherige Seite

1/79

Nächste Seite

• To minimise the release of dust, the machine

should be connected to a suitable extraction

unit. All dust extraction elements (exhaust

hoods etc.) must be properly set.

•

Wear suitable personal protective

equipment: ear protection to

reduce the risk of hearing loss;

safety goggles; a dust mask to

prevent inhalation of harmful

dust; protective gloves when

working with raw materials and when changing

tools.

• Only transport the tool in suitable packaging.

Maintenance and repair

• Replace worn table inserts.

• Only use the machine if all protection devices

are in their correct positions, the machine is in

good condition and has been well maintained.

• Faults on the machine, including the separating

guards or the tool, must be reported to main-

tenance staff immediately upon discovery. The

machine must not be used until the fault has

been eliminated.

• If the machine is equipped with a laser, ensure

it is always replaced by a laser of the same type.

Repairs must only be made by the laser manu-

facturer or an authorised agent.

Safe work

• Only process material for which the machine

has been approved.

• Never process material contain asbestos.

• Ensure that the ﬂ oor around the machine is

level, clean and free of loose objects (e.g. chips

and offcuts).

• Keep hands, ﬁ ngers and arms well away from

the rotating tool. Never reach into the area of

the saw blade behind the stop.

• Always assume the correct position before start-

ing work:

- front at the operating end,

- facing the machine,

- next to the cutting line.

• Do not remove offcuts or other workpiece parts

from the cutting area while the machine is still

running and until the saw blade stops.

• Use a suitable device to support long workpieces

and ensure that they are horizontal.

• Never allow another person to hold or support

the workpiece when sawing. Always clamp the

workpiece in a suitable device.

• Observe the speciﬁ ed maximum workpiece di-

mensions.

• Observe the instructions for lifting and trans-

porting the machine.

• Observe the instructions for installing and op-

erating the machine.

• Ensure the permissible dimensions of the saw

blade are not exceeded. Never use reducers or

adapters to secure the saw blade on the tool

spindle.

• Do not saw wood containing metal parts such

as nails, screws, etc.

• Do not apply lateral force to the saw blade.

• Always saw only one workpiece. It is not possible

to safely secure several workpieces; they can

displace each other during sawing and block

the saw blade.

• If the saw blade is blocked, switch the machine

off immediately and disconnect the mains plug.

Do not remove the jammed workpiece until you

have done this.

• Always guide the saw unit steadily upwards by

hand after the cut and never release it in the

lower position.

• Never open the pivot guard by hand when work-

ing.

• Only for AS/NZS: The tool shall always be sup-

plied via residual current device with a rated

residual current of 30 mA or less.

4.3 Emission levels

Levels determined in accordance with EN 61029

are typically:

Measured acceleration < 2.5 m/s

Sound pressure level 90 dB(A)

Noise level 103 dB(A)

Measuring uncertainty allowance K = 3 dB

Wear ear protection.

The speciﬁ ed emissions values (vibration, noise)

– are used to compare machines.

– They are also used for making preliminary

estimates regarding vibration and noise loads

during operation.

– They represent the primary applications of the

power tool.

Increase possible for other applications, with oth-

er insertion tools or if not maintained adequately.

Take note of idling and downtimes of machine!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool SYM70E Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info