Bedienungsanleitung Festool TCL 6 DUO (Seite 13 von 62) (Alle Sprachen)

796192

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

4 Intended use

Chargers suitable

– For internal use only.

– For charging Festool Li-ion battery packs

BP, BPS and BPC with the following rated

voltages and capacities:

10.8 V (3S1P) 1.3 Ah, 1.5 Ah

10.8 V (3S2P) 2.6 Ah, 3.0 Ah, 4.2 Ah

14.4 V (4S1P) 1.3 Ah, 1.5 Ah

14.4 V (4S2P) 2.6 Ah, 3.0 Ah, 4.2 Ah, 5.2 Ah*

18.0 V (5S1P) 1.3 Ah, 1.5 Ah, 2.6 Ah, 3.1 Ah*,

4.0 Ah*

18.0 V (5S2P) 2.6 Ah, 3.0 Ah, 4.2 Ah, 5.2 Ah*,

6.2 Ah*

* Rapid charging battery packs

The user is liable for improper or non-in

tended use.

5 Parts of the device

[1-1] Charging station

[1-2] Battery pack

[1-3] Remaining charge time display (SCA 8

only)

[1-4] Charge status display

[1-5] Mains power cable rewind

[1-6] Vents (SCA 8 only)

[2] Wall mount for charger

The specified illustrations appear at the begin

ning of the Operating Instructions.

6 Commissioning

WARNING

Unauthorised voltage or frequency.

Risk of accidents

► The mains voltage and the frequency of the

power source must correspond to the

specifications on the name plate.

► In North America, only Festool machines

with the voltage specifications 120 V / 60 Hz

may be used.

6.1 Start charging

WARNING! Before commissioning, completely

unwind the mains power cable from the cut-

out [1-5].

► Insert the charger's mains plug in the sock

et.

► Push the battery pack [1-2] into the charg

ing station [1-1].

6.2 Wall mounting

See figure [2].

7 Operation

7.1 Meaning of the LEDs

After commissioning the charger, the LED of

the charge status display [1-4] switches to yel

low.

SCA 8 self-check

Before the LED of the charge status display

switches to yellow, all LEDs [1-3] and [1-4] as

well as fans [1-6] switch on for approx. 1 s.

Operating statuses of the charger:

LED yellow – steady light

Charger is ready to use.

LED green – flashing

Battery pack is charging.

LED green – steady light – READY

The battery pack is > 80% charged and ready for

use. In the background, the battery pack will

continue to be charged up to 100%.

READY

LED red – flashing

General fault indicator, e.g. not in full

contact, short circuit, faulty battery pack, etc.

LED red – steady light

Battery temperature is outside the per

mitted range. As soon as the permitted temper

ature is reached, the charger automatically

switches to charging.

Remaining charge time (SCA 8 only)

Display of anticipated remaining charge

time:

> 45 min

30 min

15 min

5 min

► Insert the battery pack.

The charge status display [1-4] flashes several

times.

Anticipated remaining charge time is displayed

by the corresponding LED [1-3] flashing.

7.2 Working instructions

Continuous or several consecutive charging cy

cles can cause the charger to heat up. However,

this does not do any harm and does not indicate

a technical fault.

When kept in the charger, battery packs remain

fully charged.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool TCL 6 DUO Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info