778616
19
Zoom out
Zoom in
Vorherige Seite
1/102
Nächste Seite
8.5 Festool Work App
The power tool can be configured with the
Festool Work app.
The battery pack is connected via
Bluetooth®, see the operating manual for
the battery pack.
9 Tool holder, attachments
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
CAUTION
Risk of injury from hot and sharp insertion
tool
Do not use any blunt or faulty insertion
tools.
Wear protective gloves when handling an
insertion tool.
Prior to initial use: Apply some multipur
pose grease to the drill spindle.
9.1 CENTROTEC tool chuck [7]
Fast changeover of tools with CENTROTEC
shaft.
WARNING! Only clamp CENTROTEC tools in
CENTROTEC tool chucks.
Wear gloves when replacing tools.
9.2 Chuck [8]
For clamping drill bits and bits with max. shaft
diameter of 13 mm.
WARNING! Clamp the tool centrally in the
chuck.
9.3 Angle attachment [9]
Drilling and screwdriving at right angles to the
power tool (available as an accessory depend
ing on the model).
9.4 Tool holder in the drill spindle [10]
Bits can be inserted directly into the hexagon
socket holder of the drill spindle.
9.5 Eccentric adapter [11]
Screwdriving close to edges with bits according
to ISO 1173 (available as an accessory depend
ing on the model).
9.6 Depth stop [12]
The depth stop (available as an accessory de
pending on the model) allows a screw to be
tightened with a defined depth. You can set the
dimension to which the screwhead is to project
over the workpiece surface, or to which it is to
be inserted.
Depth adjustment
Firmly set the required screw-
in depth by turning the hous
ing [12-1]. Each catch alters
the screw-in depth by 0.1 mm.
To unscrew a screw, the A/B sleeve must first
be removed.
10 Working with the electric
power tool
WARNING
Risk of injury
Only position the power tool on the screw
when it is switched off.
Always secure the workpiece in such a
manner that it cannot move during ma
chining.
Keep hands away from the rotating tools.
CAUTION
Risk of burns
The tool holder and tool may become very
hot during operation.
Allow them to cool down before attaching
them to the belt clip.
10.1 Kickback stop
WARNING
Risk of injury
The kickback stop does not guarantee com
plete protection against a kickback.
Always concentrate on your work and refer
to the safety instructions and warnings.
The kickback stop is triggered if the tool
is jammed, causing the power tool to
rotate around the screw axis suddenly
and unexpectedly. The power tool switches off,
beeps once and the LED light flashes continu
ously.
After the kickback stop has been triggered:
Release the on/off switch [1-5].
Eliminate the cause of the jam.
English
19
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool TDC 18-4 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info