574934
16
Zoom out
Zoom in
Vorherige Seite
1/90
Nächste Seite
16
TI 15
GB
Turn the clamping ring as far as the stop to se-
cure the adapter.
Angle attachment DD-AS [7]
Drilling and screwing at right angle to machine
(partly as an accessory).
Eccentric attachment DD-ES [8]
Screwdriving near edges with bits according to ISO
1173 (partly as accessory).
9 Working with the machine
9.1 Operating modes
Depending on the tool holder / adapter selected,
the machine is operated as follows:
9.2 On/Off switch [1-2]
Press = ON, release = OFF
Depending on the pressure applied to the ON/
OFF switch the speed/impact rate can be con-
trolled continuously.
The LED bulb
[1-4]
lights up when the ON/OFF
switch is pressed
[1-2]
.
9.3 Bit depot [1-1]
Magnetic, for storing bits and bit holders.
9.4 Belt clip [1-9]
For short-term fixing of the device to work attire:
can be moved to the right or left or can also be de-
tached from the battery pack.
9.5 Acoustic warning signals
Acoustic warning signals sound and the machine
switches off in the following operating states:
10 Service and maintenance
Customer service and repair
only
through manufacturer or service
workshops: Please find the nearest
address at:
www.festool.com/Service
Use only original Festool spare parts!
Order No. at:
www.festool.com/Service
Note the following information:
Keep the ventilation slits on the machine free and
clean to ensure adequate cooling.
Keep the contacts on the machine, charger and
battery pack clean.
Information on battery packs
Store in a cool, dry place at a temperature be-
tween 5 °C and 25 °C.
Protect battery packs from moisture, water and
heat.
Do not leave flat battery packs in a charger dis-
connected from the mains power supply for lon-
ger than one month. Danger of deep discharge!
If you intend to store li-ion battery packs for lon-
ger periods without use, you should charge them
to 40 % capacity (approx. 15 min charging time).
Screwing with impact
WH-CE CENTROTEC tool chuck (see
Chapter CENTROTEC tool chuck [4])
Screwing and drilling without impact
TI-FX adapter (see Chapter TI-FX adapter
[6])
DD-AS elbow adapter
DD-ES eccentric attachment
DD-DC screwdriver attachment
– BF-TI 13 chuck (see Chapter BF-TI 13
chuck [5])
WARNING
Risk of injury
Only place the machine on the nut/screw when
switched off.
Battery flat or machine over-
loaded.
Change the battery.
Place the machine under reduced
stress.
Machine is overheating.
You must allow the machine to
cool before using again.
LiIon battery pack is faulty or has
overheated.
Once the battery pack has cooled,
perform a functional check using
the charger.
WARNING
Risk of injury, electric shock
Always disconnect the battery pack from the
machine before any maintenance or care work!
All maintenance and repair work which requires
the motor housing to be opened, must only be
carried out by an authorised service workshop.
EKAT
1
2
3
5
4
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool TI 15-14.4 V wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info