778502

Festool TKS 80 EBS Seite 30

30
Zoom out
Zoom in
Vorherige Seite
1/276
Nächste Seite
and balance. It should be installed in an
area that provides enough room to easily
handle the size of your workpiece. Cram
ped, dark areas, and uneven slippery floors
invite accidents.
–Frequently clean and remove sawdust
from under the saw table and/or the dust
collection device. Accumulated sawdust is
combustible and may self-ignite.
–The table saw must be secured. A table
saw that is not properly secured may move
or tip over.
–Remove tools, wood scraps, etc. from the
table before the table saw is turned on.
Distraction or a potential jam can be dan
gerous.
–Always use saw blades with correct size
and shape (diamond versus round) of ar
bour holes. Saw blades that do not match
the mounting hardware of the saw will run
off-centre, causing loss of control.
–Never use damaged or incorrect saw
blade mounting means such as flanges,
saw blade washers, bolts or nuts. These
mounting means were specially designed
for your saw, for safe operation and opti
mum performance.
–Never stand on the table saw, do not use it
as a stepping stool. Serious injury could
occur if the tool is tipped or if the cutting
tool is accidentally contacted.
–Make sure that the saw blade is installed
to rotate in the proper direction. Do not
use grinding wheels, wire brushes, or
abrasive wheels on a table saw. Improper
saw blade installation or use of accessories
not recommended may cause serious in
jury.
2.3 Further safety instructions
–
Wear suitable personal protective equip
ment: Ear protection, protective goggles,
dust mask for work that generates dust
and protective gloves for changing tools.
– Faults on the power tool, including the sep
arating guards or the tool, must be repor
ted to maintenance staff immediately. The
machine must not be used until the fault
has been eliminated.
– Check the plug and cable on a regular ba
sis and, if they are damaged, have them re
placed by an authorised customer service
workshop.
– Use of your own aids e.g. rulers, etc. is not
permitted.
–Only for AS/NZS: The tool shall always be
supplied via residual current device with a
rated residual current of 30 mA or less.
2.4 Safety instructions for the pre-
assembled saw blade
Usage
– The maximum speed specified on the saw
blade must not be exceeded and the speed
range must be adhered to.
– The pre-installed saw blade is only de
signed for use in circular saws.
– Proceed with extreme care when unpack
ing, packing and handling the tool (e.g. in
stalling it in the machine). There is a risk of
injury from extremely sharp cutting edges!
– When handling the tool, wearing safety
gloves provides a more secure hold of the
tool and further reduces the risk of injury.
– Circular saw blades with cracked bodies
must be replaced. Repair is not permitted.
– Circular saw blades with a combination de
sign (soldered saw teeth) with saw tooth
thickness smaller than 1 mm must no lon
ger be used.
–WARNING! Do not use tools with visible
cracks or blunt or damaged cutting edges.
Installation and mounting
– Tools must be clamped in such a way that
they cannot come loose during operation.
– When assembling the tools, it must be en
sured that the clamping takes place on the
tool hub or the clamping surface of the
tool, and that the cutting edges do not
come into contact with other components.
– Do not lengthen the key or tighten by hitting
with a hammer.
– The clamping surfaces must be cleaned to
remove contamination, grease, oil and wa
ter.
– Clamping screws must be tightened ac
cording to the manufacturer's instructions.
– Only securely installed rings, e.g. rings that
have been pressed in or those that are held
in position by an adhesive bond, may be
used to adjust the hole diameter of circular
saw blades to the spindle diameter of the
machine. The use of loose rings is not per
mitted.
English
30
… 30 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool TKS 80 EBS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info