Bedienungsanleitung Festool ts 55 ebq-plus-fs (Seite 16 von 94) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch)

382565

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

in the workpiece. The riving knife is ineffective

in preventing kickback during short cuts.

e) Do not operate the saw if riving knife is bent.

Even a light interference can slow the closing

rate of a guard.

2.3 Noise and vibration information

Typical values established in compliance with EN

60745:

Sound-pressure level/ Sound-power level

TS 55 EBQ/TS 55 EQ 95/106 dB(A)

TS 55 Q 96/107 dB(A)

Measuring uncertainty allowance K = 3 dB

Wear ear protection.

Overall vibration levels (vector sum for three direc-

tions) measured in accordance with EN 60745:

Vibration emission level (3 directions)

Sawing wood a

< 2,5 m/s²

Sawing metal a

< 2,5 m/s²

Uncertainty K = 1,5 m/s²

The emission values speciﬁ ed (vibration, noise)

were measured in accordance with the test con-

ditions stipulated in EN 60745 and are intended

for machine comparisons. They are also used for

making preliminary estimates regarding vibration

and noise loads during operation.

The emission values speciﬁ ed refer to the main

applications for which the power tool is used. If the

electric power tool is used for other applications,

with other tools or is not maintained sufﬁ ciently

prior to operation, however, the vibration and noise

load may be higher when the tool is used. Take into

account any machine idling times and downtimes to

estimate these values more accurately for a speci-

ﬁ ed time period. This may signiﬁ cantly reduce the

load during the machine operating period.

3 Power supply and start-up

The mains voltage must correspond to

the speciﬁ cation on the rating plate.

Always switch the machine off before

connecting or disconnecting the mains

lead!

See Fig. 2 for connection and disconnection of the

power cable.

The switch [1-8] is for switching on/off (push = ON,

release = OFF).

The switch can only be activated after the switch

lock [1-9] has been pushed up.

Activating the switch lock simultaneously locks

the plunging equipment and the sawing unit can

be moved down against the spring force. This

causes the saw blade to emerge from the protec-

tive cover.

When the machine is lifted, the sawing unit springs

back into the starting position.

Only guide the machine against the work-

piece when it is switched on.

Check the installation ﬁ xture prior to use

and do not use the machine if the ﬁ xture

does not function correctly.

4 Machine settings

Always pull the plug out of the socket be-

fore making settings.

4.1 Electronics

The TS 55 EBQ/TS 55 EQ features full-wave

electronics with the following properties:

Smooth start-up

The smooth start-up ensures the machine starts

up jolt-free.

Speed adjustment

You can regulate the speed steplessly between 2000

and 5200 rpm using the adjusting wheel [1-6]. This

enables you to optimise the cutting speed to suit

the material (see table 1).

Constant speed

The pre-selected speed remains constant whether

the machine is in operation or in neutral position.

Temperature cut-out

To prevent overheating, the safety electronics

switches the machine off when it reaches a critical

motor temperature. Let the machine cool down

for approx. 3-5 minutes before using it again. The

machine requires less time to cool down if it is

running, i.e. in neutral position.

Current limiting

Current limiting prevents permissibly high current

consumption under extreme overload. This can

lead to a decrease in the motor speed. The motor

immediately restarts after the load is removed.

Brake (only TS 55 EBQ)

After switching-off the tool, the saw blade is elec-

tronically brought to a standstill in 1.5 – 2 sec-

onds.

4.2 Cutting depth

The cutting depth can be set at 0 – 55 mm:

- Press the cutting depth stop [2-3] and move it to

the desired cutting depth (the values speciﬁ ed on

the scale [2-1] apply to 0° cuts without guide rail),

- Release the cutting depth stop (the cutting depth

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool ts 55 ebq-plus-fs Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info