Bedienungsanleitung Festool TS 55 FQ (Seite 24 von 150) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

778505

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

7 Settings

WARNING

Risk of injury, electric shock

► Always disconnect the mains plug from the

socket before performing any work on the

machine.

7.1 Electronics

The machines TS 55 FEBQ, TS 55 FEQ come

with full-wave electronics with the following

properties:

Smooth start-up

The electronically controlled smooth start-up

function ensures that the power tool starts up

smoothly.

Constant speed

The motor speed is electronically kept con

stant. This ensures a uniform cutting speed

even when under load.

Speed control

You can continuously adjust the speed within

the speed range using the adjusting

wheel [1-10] (see "Technical data"). This ena

bles you to optimise the cutting speed to suit

each surface.

Speed range per material

Solid wood (hard, soft) 6

Chipboard and hardboard 3–6

Laminated wood, blockboard, veneered

and laminated panels 6

Laminate, mineral materials 4–6

Plaster- and cement-bonded chipboard

and fibreboard 1–3

Aluminium panels and profiles up to

15 mm 4–6

Plastics, fibre-reinforced plastics, paper

and fabric 3–5

Acrylic glass 4–5

Current limiting

Current limiting prevents excessive current

consumption under extreme overload, which

can lead to a decrease in the motor speed. The

motor immediately restarts after the load is re

moved.

Brake

The saw TS 55 FEBQ comes with an electronic

brake. The saw blade is stopped electronically

within approximately two seconds of switching

off the machine.

Temperature cut-out

The power supply is restricted and the speed

reduced if the motor exceeds a certain temper

ature. The power tool continues operating at re

duced power to allow the ventilator to cool the

motor quickly. The power tool starts up again

automatically once the motor has cooled suffi

ciently.

7.2 Adjusting the cutting depth

The cutting depth can be set at 0 – 55 mm at the

cutting depth stop [3-1].

The saw unit can now be pushed downwards as

far as the cutting depth that is set.

Cutting depth without guide rail

max. 55 mm

+FS

Cutting depth with FS guide rail

max. 51 mm

7.3 Setting the cutting angle

between 0° and 45°:

► Unscrew the rotary knobs [4-1].

► Swivel the saw unit to the desired cutting

angle [4-2].

► Tighten the rotary knobs [4-1].

Both positions (0° and 45°) are set at the

factory and can be readjusted by the cus

tomer service team.

When making angled cuts, slide the view

ing window/splinter guard to the highest

position.

To undercut -1° and 47°:

► Swivel the saw unit to the end position (0°/

45°) as described above.

► Pull out the release button [4-3] slightly.

► For -1° undercuts, also pull the release

button [4-4].

The saw unit engages in the -1°/47° position.

► Tighten the rotary knobs [4-1].

7.4 Selecting the saw blade

Festool saw blades are identified by a coloured

ring. The colour of the ring represents the ma

terial for which the saw blade is suited.

Refer to the necessary saw blade data (see sec

tion 3.1).

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool TS 55 FQ Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info