Bedienungsanleitung Festool TS 55 FQ (Seite 27 von 150) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

778505

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

Always use original Festool spare

parts. Order no. at:

www.festool.co.uk/service

EKAT

235

The tool is equipped with special self-discon

necting carbon brushes. If they wear out, the

power supply is disconnected automatically and

the tool stops.

Observe the following instructions:

► Damaged safety devices and parts, such as

a faulty lever for changing tools [1-5], must

be properly repaired or replaced in a recog

nised specialist workshop, unless otherwise

indicated in the operating manual.

► Check the condition and fault-free function

ing of the recuperating springs, which push

the entire drive mechanism bearing into the

upper protected end positions.

► To ensure constant air circulation, always

keep the cooling air openings in the housing

clean and free of blockages.

► Use an extractor on all openings in order to

remove wood chips and splinters from the

power tool. Never open the protective

lid [1-18].

► When working with plaster- and cement-

bonded fibreboards, clean the tool particu

larly thoroughly. Clean the vents of the

power tool and on/off switch using dry, oil-

free compressed air. Otherwise, gypsum

dust deposits may build up inside the power

tool's housing and on the on/off switch and

harden when exposed to humidity. This may

impair the switching mechanism

9.1 Reconditioned saw blades

You can use the adjusting screw [8-1] to pre

cisely set the cutting depth for reconditioned

saw blades.

► Set the cutting depth stop [8-2] to 0 mm

(with guide rail).

► Unlock the saw unit and push it downwards

as far as the stop.

► Screw the adjusting screw [8-1] in until the

saw blade comes into contact with the

workpiece.

9.2 Saw table wobbles

The saw table must be on an even surface

when adjusting the cutting angle.

If the saw table wobbles, the setting must be

implemented again (Section 7.3).

10 Accessories

Always use accessories and consumable mate

rials approved by Festool. See Festool cata

logue or www.festool.com.

The power tool may become unsafe and lead to

serious accidents if other accessories and con

sumables are used.

In addition to the accessories described,

Festool also provides a comprehensive range of

system accessories that allow you to use your

machine more effectively and in diverse appli

cations, e.g.:

• Parallel stop, table widener PA-TS 55

• Side-mounted cover, false joint ABSA-TS

• Kickback stop FS-RSP

• Parallel stop FS-PA and guide extension

FS-PA-VL

• Multifunction table MFT/3

10.1 Saw blades, other accessories

In order to saw different materials quickly and

cleanly, Festool offers saw blades for all appli

cations and these are specially designed for

your Festool saw.

10.2 Guide system

The guide rail enables you to make clean, accu

rate cuts while simultaneously protecting the

surface of the workpiece from damage.

In conjunction with the extensive range of ac

cessories, exact angled cuts, mitre cuts and fit

ting work can be completed with the guide sys

tem. The option of attaching the guide rail se

curely using clamps [9-5] ensures safer work

ing conditions.

► Adjust the guide play between the saw table

and the guide rail using the two adjustable

jaws [9-1].

Bed in the splinter guard [9-3] before using

the guide rail for the first time:

► Set the machine speed to 6.

► Place the machine at the rear end of the

guide rail together with the complete guide

plate.

► Switch on the machine.

► Push down the machine slowly to the max.

preset cutting depth and cut along the full

length of the splinter guard without stop

ping.

The edge of the splinter guard now corresponds

exactly to the cutting edge.

Position the guide rail for sawing the

splinter guard on a test piece of wood.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool TS 55 FQ Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info