Bedienungsanleitung Festool TS 55 RQ (Seite 17 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

497612

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

TS 55



Both positions (0° and 45°) are set at the factory

and can be readjusted by the after-sales service

team.

When making angled cuts, slide the viewing

window/splinterguard to the highest posi-

tion!

to undercut -1° and 47°:



Swivel the saw unit to the end position (0°/45°)

as described above.



Pull out the release button

[4-3]

slightly.

The saw unit engages in the -1°/47° position.



Tighten the rotary knobs

[4-1]

7.4 Changing the saw blade



Before changing the saw blade, set the machine

to the 0° position and select the maximum cut-

ting depth..



Fold over the lever

[5-2]

to its end position.



Push up the switch-on lock

[5-1]

and push down

the saw unit until it engages.



Loosen the screw

[5-5]

using the Allen key

[5-



Remove the saw blade

[5-7]



Insert a new saw blade.

The rotational direction of the saw blade

[5-8]

and machine

[5-6]

must be the

same!



Insert the outer flange

[5-9]

so that the pin en-

gages in the recess on the inner flange.



Tighten the screw

[5-5]

firmly.



Fold back the lever

[5-2]

7.5 Fitting the viewing window/splinter-

guard [6]

The

viewing window

(transparent)

[6-1]

provides a

view of the saw blade and optimises dust ex-

traction.

With 0° cuts, the

splinterguard

(green)

[6-2]

also

improves the quality of the cutting edge of the

sawn-off workpiece on the upper side.



Insert the splinterguard

[6-2]



Screw the rotary knob

[6-3]

through the long

hole in the splinterguard.



Make sure that the nut

[6-4]

is seated securely

in the splinterguard.

You must bed in the splinterguard before using it:



Set the machine to maximum cutting depth.



Set the machine speed to 6.

7.6 Dust extraction

A Festool mobile dust extractor with an extractor

hose diameter of 27 mm or 36 mm (36 mm recom-

mended due to the reduced risk of clogging) can be

connected to the extractor connector

[1-8]

8 Working with the machine

Please observe all mentioned safety infor-

mations and the following rules when work-

ing:

– Only guide the machine against the workpiece

when it is switched on.

– Check the installation fixture prior to use and do

not use the machine if the fixture does not func-

tion correctly.

– Always secure the workpiece in such a manner

that it cannot move while being processed.

– Always hold the machine with two hands on the

handles

[1-4]

when performing work. This re-

duces the risk of injury and is a prerequisite for

precise work.

– Always push the machine forwards

[9-2]

, never

draw the machine towards yourself.

– Adapt the fast-feed speed to prevent the cutters

on the saw blade from overheating and prevent

plastic materials from melting during cutting.

– Make sure that all rotary knobs

[4-1]

are tight-

ened before starting work.

– Do not use the machine when the electronics are

faulty because the machine may operate at ex-

cessive speeds. An absence of the smooth start-

up function or speed control indicates that the

electronics are faulty.

For work that generates dust, wear a dust

mask.

8.1 Sawing along the scribe mark

The cutting indicator

[7-2]

displays the cutting line

for 0° and 45° cuts (without guide rail).

CAUTION

Hot and sharp tools

Risk of injury



Wear protective gloves.

WARNING

Dust hazard



Dust can be hazardous to health. Always work

with a dust extractor.



Always read applicable national regulations be-

fore extracting hazardous dust.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool TS 55 RQ Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info