Bedienungsanleitung Festool TURBO 3091 (Seite 12 von 54) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

499199

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

The extraction system must not be set up in

rooms where there is a risk of explosion or

in the proximity of ﬂ ammable substances

(e.g. solvents).

After unpacking, the extraction system can be

transported on a fork-lift truck or pallet truck. In

doing so, ensure that both transverse struts (front

and rear) of the sub-frame are seated securely on

the forks of the transport vehicle. Make sure that

the majority of the weight is located on the side of

the electric control panel.

To prevent the impermissible heating of the extrac-

tion system, the system must be located in a room

with a sufﬁ cient supply of air.

2.2 Electrical connection

The operating voltage speciﬁ ed on the

rating plate must match the voltage of the

mains power!

- For safety reasons, only operate the machine

using a totally earthed socket.

If the suction turbines turn in the direction opposite

to the speciﬁ ed direction (3.1) during installation,

two of the phases of the connector (1.12/2.11) must

be swapped. This work may only be performed by

a qualiﬁ ed electrician!

The control line (12 V~), for automatically switching

ON/OFF the extraction system, must be connected

to the connector (1.10/2.13).

2.3 Compressed air connection

For ﬁ lter cleaning, ﬁ ltered and dry compressed

air with a ﬂ ow pressure of 6 bar is required at the

compressed air connection (1.9, 2.12). A pressure

regulator with ﬁ lter and water separator must be

connected to this. Use the pressure regulator to

set a pressure of 6 bar.

 A minimum input pressure of 6 bar is required

at the pressure reducer to ensure that the hub

rotates adequately, while 4 bar is required di-

rectly at the hub.

 The turbine performs one cleaning cycle every

minute for 10 seconds. Approx. 350l of air is

required during each cleaning cycle. We recom-

mend installing a buffer container with a mini-

mum volume of 150l upstream of the turbine to

ensure the required air pulse is generated.

3 Initial operation

When in operation, the rotary switch (1.13/2.14)

must be in the AUTO position.

The extraction system is made ready for operation

by means of the main switch (1.1/2.1) (Ready for

operation = I, Off = O).

The control lamp (1.2/2.2) lights up when the sys-

tem is ready for operation.

The extraction fan only starts up when the extrac-

tion system is ready for operation and when it

receives a signal from the external control line.

Depending on the installation and pipe routing, this

signal can be triggered by switching on a connected

sander or opening a sliding valve.

The suction turbine sucks in air/dust through the

suction spout (1.11/2.6). The ﬁ ltered air ﬂ ows out

again through the outgoing air spout (1.8/2.11).

4 Filter system

The extraction system has an automatic filter

cleaning system based on the principle of the

counterﬂ ow process. The ﬁ lter is cleaned regularly

during operation and after shutdown by means of

pressure surges.

4.1 Emptying and replacing the dust bag

During the following procedure, take care

not to raise dust more than is unavoid-

able.

- Turn off the main switch (1.1/2.1).

- Open the two clips (1.5/2.7) and pull out the dust

bag container (1.7/2.9).

- Close the dust bag (1.6/2.8) so that it is dustproof,

and dispose of it in accordance with statutory

regulations.

- Check the seal (3.2) for damage. Replace a dam-

aged seal immediately.

- Insert a new dust bag (4.1). Make sure that the

dust bag is seated at the edge of the dust bag

container and that the two openings (4.2) of the

dust bag are located in the dust bag container.

- Press the air out through the two openings (4.2)

located between the dust bag and dust bag con-

tainer. The dust bag must be located at the inner

wall of the dust bag container so that it is not

pulled upwards by the ventilating pressure cre-

ated when the extraction system is switched on.

- Insert the dust bag container and close the two

clips (1.5/2.7). The upper edge of the dust bag

container must make full contact with the seal

(3.2). If required, the clamping power can be ad-

justed using the screws on the clips (1.5/2.7).

4.2 Changing the ﬁ lter

During the following procedure, take care

not to raise dust more than is unavoid-

able.

- Turn off the main switch (1.1/2.1).

- Only for Turbo 7501: open the screws (1.3) and

take off the cover (1.4).

- Only for Turbo 4001 and 3091: open the two clips

(2.5).

- Take off the extraction pipe (5.1/2.3) and com-

pressed air line (5.2/2.4).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool TURBO 3091 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info