Bedienungsanleitung Finicompressors Artic 134-25 (Seite 6 von 11) (Englisch)

456446

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Cod. 710.056.02.00 – Rev. 04 – 07.06.2001

ENGLISH

page 17 of 63

3.3 PARAMETERS PROGRAMMING

HOW TO CHANGE THE SET POINT

Press the SET key (the display will show the set point value previously set).

Change the set point value displayed using the UP / DOWN keys (the change must be made within 15

seconds after having pressed the SET key, other ways the controller goes automatically to the normal

operation mode, and the DEW POINT value will be displayed without the possibility to change the SET

POINT).

Confirm the new value by pressing the SET key (this key must be pressed within 10 seconds after the end

of the previous operation, other ways the controller goes automatically to the normal operation mode, and

the DEW POINT value will be displayed without any change to the SET POINT).

The newly entered SET POINT value will blink to confirm that new data have been accepted and stored. 15

seconds later, the controller will return to the normal operation mode.

CONTROL AND CHANGE OF CONFIGURATION PARAMETERS

Hold down the SET key for 10 seconds to access the parameters configuration menu: the display will show

in sequence the set point value, the code of the first E1 modifiable parameter, and its value).

Only if strictly necessary, use the keys UP and/or DOWN to change the value of the displayed parameter.

Press the SET key to store the value of the parameter previously changed, or to browse the parameters

without changing them.

15 seconds after the last performed operation, the controller will go automatically to the normal operation

mode.

NOTE: Changes entered for timing values will be effective only after exiting the programming, while changes to other

variables will be immediately effective.

Please remember that eventual changes to the configuration parameters of the machine could negatively affect its

efficiency. Thus, changes have to be arranged in collaboration with the manufacturer.

3.4 BEFORE START UP

Before to start the machine, make sure that all the operating parameters correspond to the nominal data.

The dryer is supplied already tested and preset for normal operation, and it doesn’t require any calibration.

Nevertheless, during few hours after start up it has to be checked for proper operation.

3.5 START UP

The operations specified below must be performed after the first start up and at each start up after a

prolonged inactive period of time due to maintenance operations, o any other reason.

 Make sure that all instructions contained in chapters INSTALLATION SITE and INSTALLATION

have been respected.

 Check for proper closure the by-pass system (if present) .

 Activate the mains and press the illuminated switch on the control panel of the dryer.

 Wait a couple of minutes to let the machine reach the standard operating parameters

 Open slowly the air outlet valve and, successively, again slowly, open the air inlet valve.

 If present, close the by-pass system.

 Check the condensate drain system for proper operation.

 Check for proper tightness and stability all the connecting tubing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Finicompressors Artic 134-25 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Finicompressors Artic 134-25

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info