456443
9
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
40069 Zola Predosa (BO) - ITALY
info@finicompressors.it
- GB -
2.3 INSTALLATION SITE
Particular care is required in selecting the installation site, as an improper location could
jeopardise the proper operation of the dryer. This unit is not suitable to be used in explosive
atmosphere, where risk of fire could exist, or in presence of gaseous or solid polluting material.
Don’t use water to extinguish fire on the dryer on in the surrounding area.
Minimal installation requirements :
Select a clean room dry, free from dust, and protected from atmospheric disturbances.
The supporting area must be smooth, horizontal and able to hold the weight of the dryer.
Minimum ambient temperature of +1 ºC.
Maximum ambient temperature of +45 ºC.
Allow at list a clearance of 1 m on each side of the dryer for proper ventilation and to facilitate eventual
maintenance operations
.
The dryer doesn't require to be fixed to the supporting surface.
2.4 ASSEMBLING
Operations to be performed by qualified personnel.
Never operate with plants under pressure.
The user is responsible to ensure that the dryer will never be operated with pressure exceeding the
nominal values. Eventual over-pressure could be dangerous both for the operator and the machine.
1
Dryer
2
Cover panel
3
Fixing to compressor
upper screw
4
Compressor
5
Fixing to compressor
lower screw
6
Compression fitting
7
Connection pipe
8
Compression fitting
9
By-pass group
10
Lifting lug
Fig. 1 Fig. 3 Fig. 4
Fig. 2
2
1
6
3
Part. A
5
4
6
7
8
9
3 3
Part. A
10
Assembling sequence :
Replace the screws No.3 of the compressor, with the (M6x45) fixing screws supplied with the dryer, and
thigh them only partially.
Tight in the air outlet of compressor the compression fitting No.6, supplied with the assembling kit.
Remove the cover panel No.2 of the dryer.
Joint the dryer with the compressor, centring the holes of the dryer frame, with the screws No.3 (Fig. 3).
To lift the dryer from the ground, use the four lifting lug No.10 (M6 with long shank) screwed into the four
holes for cover panel fixing.
Slide down the dryer, so the screws No.3 occupy the upper part of the holes (Fig. 4).
Tighten definitively the fixing screws No.3.
Tight the (M8x25) fixing screws, supplied with the assembling kit, in the position No.5 to fix finally the dryer
to the compressor.
Put the connection pipe No.7 from the compression fittings No.6 and No.8 and tighten them.
Connect and properly fasten the condensate drain pipe, in compliance with the instructions given in the
2.7 following chapter.
Slowly pressurize the plant and check for air leakage.
Reassemble the cover panel No.2
.
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Finicompressors Artic 134-EVO luchtdroger wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info