Bedienungsanleitung Finlux 32FLY970L (Seite 73 von 93) (Englisch, Schwedisch, Finnisch)

623279

Zoom out

Zoom in

Vorherige Seite

1/93

Nächste Seite

English - 71 -

Connecting to a DVD Player via

Component Sockets (YPbPr) or

Scart Cable

Some DVD players are connected through •

COMPONENT SOCKETS (YPbPr). In this case,

you must use the supplied Component video

connection cable for enabling connection. First,

plug single jack of the cable to the TV’s YPbPr

socket (side). Afterwards, insert your component

cable’s (not supplied) connectors into the plural

part of the Component video connection cable (see

illustration below). Colours of the connected jacks

should match.

To enable audio connection, use the • VGA/

Component Audio cable. First, plug single jack

of the cable to the TV. Afterwards, insert your DVD

player’s audio cable’s connectors into the plural part

of the VGA/Component audio connection cable

(see illustration below). Colours of the connected

jacks should match.

Side AV Input

Audio Cable

(Not supplied)

Side Video/Audio

Connection Cable

(Supplied)

SIDE AV

YPbPr

Side view

DVD Player

Connection Cable

(supplied)

YPbPr Video Cable

(Not supplied)

When the connection is made, switch to •

YPbPr source. See, Input selection section.

Note: To connect Y Pb Pr device, you should use

supplied component (YPbPr) connection cable

You may also connect through the • SCART input.

SPDIF

Coax.OUT

Scart

(notsupplied)



Note• : These three methods of connection perform the

same function but in different levels of quality. It is not

necessary to connect by all three methods.

Remote Control Handset

Inserting Batteries

Remove the battery cover located on the back of •

the handset by gently pulling backwards from the

indicated part.

Insert two • AAA/R3 or equivalent type batteries

inside. Observe the correct polarity (+/-) when

inserting batteries and replace the battery cover.

Note: Remove the batteries from the remote control

handset when it is not to be used for a long period.

Otherwise it can be damaged due to any leakage of

batteries. Remote range is approximately 7m/23ft.

Switching On/Off

To Switch the TV On

Connect the power cord to the 220-240V AC, 50 Hz. •

Then the standby LED lights up (The LED will blink

during the standby On/Off).

To switch the TV on from standby mode either:•

Press the “•

” button, P+ / P- or a numeric button

on the remote control.

Press the “•

” button, P/CH- or P/CH+ button on

the TV. The TV will then switch on.

Note: If you switch on your TV via P+ or P- buttons on

the remote control or on the TV set, the programme

that you were watching last will be reselected.

To Switch the TV Off

Press the “• ” button on the remote control or press

the “ ” switch on the TV, so the TV will switch to

standby mode.

To power down the TV completely, unplug the power •

cord from the mains socket.

Note: When the TV is switched to standby mode, the

standby LED can blink to indicate that features such

as Standby Search, Over Air Download or Timer is

active.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Finlux 32FLY970L Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info