Bedienungsanleitung First Alert 1039102 - Onelink (Seite 17 von 32) (Englisch)

795166

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Regular Maintenance

Alarm End of Life

This unit has been designed to be as maintenance-free as possible, but there are

a few simple things you must do to keep it working properly:

• Test it at least once a week.

• Clean the smoke/CO alarm at least once a month; gently vacuum the outside of the smoke/CO

alarm using your household vacuum’s soft brush attachment. A can of clean compressed air (sold at

computer or oce supply stores) may also be used. Follow manufacturer instructions for use. Test

the smoke/CO alarm. Never use water, cleaners or solvents since they may damage the unit.

• After cleaning test the alarm.

• If the smoke/CO alarm becomes contaminated by excessive dirt, dust and/or grime, and

cannot be cleaned to avoid unwanted alarms, replace the unit immediately.

• Relocate the unit if it sounds frequent unwanted alarms. See “Where Not To Install” for details.

Discharging the Alarm

After 10 years of operation or low battery warning, discharge the alarm by following the diagram below:

Puncture label in the dotted circle with a screwdriver and slide switch all the way to the left to DISCHARGE.

NOTE: At end of life or low battery indication (chirp): unit must be put into discharge mode

to discharge remaining stored energy in battery. Unit will no longer function once put into this

mode. Unit will resist re-mounting. Once discharged, replace alarm immediately.

IM P ORTANT: Actual battery service life depends on the smoke/CO alarm and the

environment in which it is installed. Regardless of the manufacturer’s suggested battery life, you

MUST replace the alarm immediately once the unit starts “chirping” (the “low battery warning”).

1. Puncture label on dotted circle

2. Slide switch to the left

DISCHARGE

Puncture circle

with tool, slide to

permanently

discharge.

PHOTOELECTRIC

IMPORTANT!

CARBON MONOXIDE SENSITIVITY:

If CO levels reach 70ppm,

it must activate within 60-240 minutes. At 150ppm within

10-50 minutes. At 400ppm within 4-15 minutes.

Refer to user’s manual for more information.

Installed On

Replace By

Replace alarm 10 years after installation.

CONFORMS TO

UL STD 217 & UL STD 2034

3055574

Follow and Retain User’s Manual: BRK

Brands, Inc.

1301 Joe Battle, El Paso, TX 79936.

Customer Service Team: 1(833) ONE-LINK

www.rstalert.com (1-833-663-5465)

BLACK

•

LINE

ORANGE

•

INTERCONNECT

WHITE

•

NEUTRAL

WARNING!

Carbon monoxide cannot be seen or smelled but can kill

you. If alarm signal sounds: 1. Operate Test/Silence button.

2. Call your emergency services. (Fire Dept. or 911)

3. Immediately move to fresh air - outdoors or by an open door/window.

HOW TO DISCHARGE ALARM:

Puncture circle with tool and slide as indicated to

permanently discharge battery. Once discharged, the alarm

cannot be reactivated and must be replaced.

MAINTENANCE AND TESTING:

Alarm is sealed, with no serviceable parts. Battery is not

replaceable. Constant use at high or low temperatures or

high humidity may reduce battery life. Test after installation,

weekly, and after cleaning. Clean monthly – gently vacuum

or use clean compressed air to remove dust. Never use

water, cleaner or solvent, since this may damage the unit.

ALARM GUIDE:

SMOKE ALARM: Three beeps. Three red ashes.

CO ALARM: Four beeps. Four red ashes.

MALFUNCTION: Three “chirps” per minute. Three yellow ashes. Replace alarm.

END OF LIFE: Five “chirps” per minute. Five yellow ashes. Replace alarm.

LED light indicates AC power

SINGLE AND/OR MULTIPLE STATION

SMOKE & CO ALARM

MODEL NO. 1039102

120V AC 134 mA 3.0 Lithium Battery Backup

SMOKE SENSITIVITY: 1.15%-3.20% ft OBSC.

HOW TO ACTIVATE ALARM:

NOTE: Ensure the AC Plug is connected rst prior to

mounting the unit to activate battery back-up.

Install the mounting bracket, align the base of the

alarm to the mounting bracket and turn clockwise.

Contains Transmitter Modules FCC ID:2ANOG-A76F