Bedienungsanleitung First Alert 3040DFE (Seite 4 von 4) (Englisch)

795094

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

English

Getting Started

English

Programming your

Personal Passcode

STEP 4: Opening your Security

Box using the pre-set factory

code

THE PRE-SET FACTORY CODE IS 3*

Using the keypad, enter the factory pre-set

code. The LED will flash a green light and

stay green for 10 seconds after the

button is pressed. You will hear the

Security Box unlock.

NOTE: You have 10 seconds to open the

Security Box. If the green light goes out,

you will have to re-enter the code.

To open, turn the knob from the locked

position to the unlocked position, one

quarter turn counter-clockwise. To open, lift

from the outer edge of the lid. (fig.2)

If the LED light flashes red after you enter

the code, this means the code was entered

incorrectly and the Security Box will not

open.

NOTE: If an incorrect code is entered 3

times in a row, the Security Box will

automatically shut down for 4 minutes

before it can be opened again using the

correct code. During this delay, the

Override Key can be used to open the

Security Box.

NOTE: For your security, immediately

re-program the digital lock to your

Personal Passcode.

Open your Security Box with the Override

Key or with the pre-set factory Passcode.

On the inside of the lid, find and press

the red button located to the side of the

battery compartment (Fig.3). The LED light

above the keypad will flash orange.

Enter your personal Passcode, up to 5

digits, followed by the button and then

repeat a second time. You must enter

the number twice.

For example: 1 2 3 4 5 - 1 2 3 4 5

After the first entry, the LED will flash orange.

After the second entry, the LED will flash

green and then go out.

Your Personal Passcode is now saved.

Write it down and store it in a secure place

away from the Security Box.

Close the lid of your Security Box and

return the knob to the locked position (Fig. 6).

If the override key was used, turn to the

locked position, remove and replace the

lock cover.

NOTE: The factory pre-set code is no longer active and cannot

be used to open the Security Box.

STEP 1: Locate Override Keys

Keys and batteries are stored in the packing

material. Remove them before discarding

the box.

STEP 2: Opening your Security

Box using your Override Key

Remove cover from key lock.

Insert Override Key into key lock and turn

the key counter clockwise one quarter turn

to the unlocked position.

Turn the knob counter-clockwise one

quarter turn to the unlocked position. (fig.1)

To open, lift from the outer edge of the lid.

(fig.2)

STEP 3: Installing Batteries

Locate the battery cover on the back side

of the lid. (fig.4)

Slide the cover off the battery

compartment.

Properly insert batteries, noting correct

direction, replace cover and close the

Security Box lid.

Return the Override Key and the knob to

the locked position.

NOTE: Clean the battery contacts in the battery

compartment and on the batteries before

installing new batteries.

Closing and Securing your

Security Box

Be careful not to overfill your Security Box

or obstruct the door from completely

closing.

Make sure knob is in the unlocked position.

Make sure lid is closed completely. (Fig. 5)

Turn the knob from the unlocked position

one quarter turn clockwise to the locked

position. Your Security Box should now be

secured.

NOTE: While the override key is in the

unlocked position you can open and close

the Security Box by turning the knob from

the locked to the unlocked position and

back again without entering your personal

code. To secure your Security Box, make

sure that you have turned the override key

to the locked position and have stored the

key away from the Security Box in a safe

place.

Troubleshooting

No light from LED: This indicates that the

batteries are expired and need to be

replaced. To change the batteries, see

Getting Started STEPS 2 & 3.

NOTE: Replacing batteries does not

erase your personal code.

The LED is blinking a red light:

This means that your batteries are low. To

change your batteries, see Getting Started

STEPS 2 & 3.

Warning: DO NOT FORCE THE KNOB

If forced, the knob will break and your

Security Box will be damaged. When

operated correctly, the knob will function

so that it can be turned easily into the

opened position.

If you have additional questions while

operating your Security Box, please

contact BRK Brands Europe Ltd.

Security Cable

INSIDE

VIEW

Left side

panel

Back panel

EXTERIOR

SIDE VIEW

EXTERIOR

SIDE VIEW

Press Here

Remove the plug from

security cable

attachment hole.

Loop cable around

desired object and then

through itself.

Depress cable release

button and while holding

down, insert security

cable into the hole as

shown in diagram, then

release button.

Model 3040DFE

includes security cable.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

First Alert 3040DFE Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info