Bedienungsanleitung First Alert DVR0805 (Seite 27 von 47) (Englisch)

795160

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

Page 27

Network Setup for Remote Access

Use the NETWORK SETUP menu to conﬁgure your network and DNS

settings for remote access. If you are only going to access the DVR locally

from a computer attached to the same router as the DVR, you only need to

conﬁgure settings using either the DHCP or STATIC IP. Because you are on

the same network, port forwarding and knowing the public IP address are

not necessary. You will just access the DVR by entering the IP address of the

DVR from the NETWORK setup into the Internet Explorer browser window.

If you are going to take advantage of the Remote Surveillance feature, such

as for a smart phone or to view your system outside of your network over

the internet you will need to review and set up Port Forwarding and the

DDNS. After you setup the NETWORK settings using DHCP , STATIC IP or

DDNS, see the REMOTE SURVEILLANCE section for further instructions.

There are ﬁve options for conﬁguring the DVR to be accessed remotely:

DHCP, Static IP, UPnP, PPPOE, and DDNS. To access this menu, from the

MAIN MENU click ADVANCED then NETWORK SETUP. Be sure your router

or network is connected to the LAN port on the back of the DVR.

DHCP (Dynamic Host Conﬁguration Protocol)

DHCP is a protocol used by networked devices (clients) to obtain various parameters necessary for the clients to operate

in an Internet Protocol (IP) network. It allows you to quickly connect to your network and obtain an IP address from the

router. After the initial setup, we recommend that you disable DHCP, then select STATIC from the TYPE drop down box

and set the IP address between 1~100. For example, if your IP address is 192.168.0.107, change the last digits to 90 (i.e.

192.163.0.90). This ensures that port forwarding will not change in the event of power failure or resetting of your network.

To conﬁgure DHCP settings:

1. Select DHCP from the TYPE drop down box in the NETWORK SETUP Menu. You should see the message

“Getting IP...” The router will assign an IP address. This is the IP address you will forward port 80 to on the

router so you can access the DVR from remote computers See comment above to conﬁgure a static IP.

2. Click APPLY. Click OK in the conﬁrmation window.

3. If necessary, change the Media and Web Port settings

Static IP

You will need to setup the network settings on the DVR to match the settings of the router to which your DVR is connected.

This information can be obtained through your computer. Windows 7, Vista or XP all have similar ways to access this data.

To get the router settings:

1. To access the router’s settings you will need to enter the Command (CMD) panel on

your computer. It must be connected to the same router as your DVR.

• In Windows 7 or Vista, from the “START” menu type “CMD” in the ﬁeld that says, “Search

programs and ﬁles” and hit ENTER or click on the magnifying glass icon.

• In Windows XP select “Run” from the “START” menu. Type “CMD” after the prompt

2. Type “ipconﬁg” at the prompt and hit enter

3. You will get a screen that contains information similar to what is shown below. Within all of the

information shown, locate the IPv4, Subnet Mask and Gateway addresses. These you will enter

into the STATIC IP screen in the NETWORK SETTINGS menu in your DVR. See next step.

REMOTE ACCESS

NETWORK SETUP

Network Setup

Windows “ipconﬁg” Info Example

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

First Alert DVR0805 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info