Bedienungsanleitung First Alert PRO-D1610 (Seite 25 von 48) (Englisch)

795212

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Page 25

Advanced Operation

PTZ

Pan tilt zoom...PTZ

Pan/Tilt/Zoom (PTZ) Setup:

NOTE: Consult the instruction manual of your PTZ camera for complete

information about your camera, including protocol, baud rate and parity

settings before beginning setup. Enter these settings in the DVR.

Step 1: Connect your PTZ Camera to this DVR

Connect a PTZ camera to the BNC and DC power cables. Also,

connect the communication cable from the PTZ camera to the 485A

(TX, +) and 485B (RX, -) control inputs to the Alarm/PTZ block on the

back of the DVR. Note there are two sets of PTZ control connections

(485A-1/485B-1 & 485A-2/485B-2). Multiple PTZ cameras can be set up

with each by making parallel connections. See diagram for details and

see “PTZ Camera Setup” Info box for additional information.

Step 2: Conﬁgure PTZ Communication Settings:

To access this menu, from the MAIN MENU click DEVICES then PTZ (see PTZ

Setup image). Use the slider bar on the right of the screen to access all 8

channels available on this DVR. The PTZ setting options for each camera can be

selected independently and are available next to each camera’s channel number.

1. Under PROTOCOL, select PELCO-D or PELCO-P for the selected channel.

2. Under BAUD RATE, select 1200, 2400, 4800, or 9600.

3. Under PARITY, select ODD, EVEN, MARK, SPACE, or NONE parity bits. Note:

Mark = 1, Space = 0 parity bits.

4. Under ADDRESS, provide an address from 001~255 using the Virtual Key-

board for each PTZ camera.

5. Click APPLY. Click OK in the REMARK window.

6. Click EXIT in all menus until all windows are closed.

Step 3: Conﬁgure the Operation & Control of your PTZ

Camera(s):

After your PTZ camera(s) are set up you can control their

operation from your DVR. Note: Individual features must be

available on your camera to operate.

1. In Live View, double click on the Channel with the connected

PTZ Camera to open to full screen view. This selects the

channel to conﬁgure and control.

2. From the Quick Access Menu select PTZ. (See image at left)

3. From the PTZ CONTROL screen you can adjust:

• Pan Speed (3-63): Adjusts the speed the camera will move.

• Zoom: “+” Zooms in and “-” zooms out

• Focus: “+” and “-” focuses the picture.

• Iris: “+” lets more light in and “-” removes light from the picture. This is useful to correct

backlight issues.

• Directional keys: Left and Right Arrows control the pan; Up and Down arrows control the tilt.

PTZ Camera Setup

NOTE: It is recommended for best results to use 120Ω

shielded twisted pair cable of a sufﬁcient gauge to meet

your application length. 18 to 22 gauge is usually sufﬁcient.

In addition, be sure to only install the 120Ω terminating

resistor that comes with your PTZ camera in the last parallel connected

camera. Keeping that resistor in all cameras can possibly degrade the

signal and can cause unexpected or loss of operation and control.

Install 120 Ω

terminating

resistor in last

camera only

PTZ Inputs Conguration

485A-1

485B-1

GND

NO1

COM2

ALM IN

GND

+ 12V

GND

485A-2

485B-2

COM1

NO2

GND

BA BA BA

Note: Use similar setup for PTZ inputs 485A-2 & 485B-2

PTZ Setup

Select PTZ from the

Quick Access Menu

PTZ Control - Sub Menu

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

First Alert PRO-D1610 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info