Bedienungsanleitung First Alert PRO16810-600CA (Seite 19 von 47) (Englisch)

795188

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

Page 19

BASIC OPERATION

RECORDING

Motion Detection Setup

Motion detection is conﬁgurable on each channel. Conﬁgure motion

detection as follows:

1. Right click and select Setting click DEVICE. Then click MOTION DETECT.

This will bring up the Motion Detection Main screen.

2. Use the drop down box to select the channel to conﬁgure.

3. Click the ENABLE MD checkbox to activate the motion detection on this

channel.

4. Click on SET MD to reach the Motion Detection Sensitivity Screen which

allows the setting of the sensitivity level of detection.

5. Set the sensitivity by clicking within the Sensitivity

+ - rectangle to the appropriate level desired.

6. Click OK on the MD SETUP screen and then OK again

on the MOTION DETECT screen to conﬁrm.

7. By default, any motion with the entire camera view will activate motion

detection. The DVR system will allow you to limit motion detection

within the camera area as desired. To choose an area to enabling

motion detection, place the cursor inside the camera view of the

Motion Detection Sensitivity Screen. Drag and click over the area

you want motion to be detected. A green rectangle is formed. Up

to four areas can be created. The result is that the area within any

of the green rectangles will detect motion. Click OK to conﬁrm.

Motion Detection Alarm Settings

Motion detection can trigger recordings, buzzer alarms, an alarm output

control signal, and a preset position on a connected PTZ camera –

(purchased separately.) To set Motion Detection alarms do the following:

1. Click SET ALARM in the Motion Detect screen.

The ALARM SETTING screen will appear.

2. Alarm Duration: Input the duration of the alarm

in number of seconds. (1 – 9999999)

3. Buzzer: Place check mark in box if you want a

buzzer to sound locally from the DVR.

4. Client: Send message to client.

5. Record: Allows the selection of which camera records based off

motion detection. For instance, motion detected from camera channel

1 can activate motion on any of the other camera channels (1-16.)

6. Alarm Output: Place check mark in box if you want to send an

output control signal to a connected device. The device must

be connected to the output terminal on the alarm block on the

rear panel of the DVR. The control signal provided is 24 Vdc.

7. Preset: Place check mark in box to control a connected PTZ

camera to a PRESET position, such as an entry door or cash

box. Make sure the PTZ camera is connected to the channel

selected. Input the correct preset location as desired.

CCTV Resolution

CCTV resolution is measured in vertical and horizontal pixel dimensions and typically

limited by the capabilities of both the camera and the recorder that you are using for your

CCTV surveillance installation. CCTV systems use an analog video signal. For television

speciﬁcations (which CCTV uses) the highest resolution that can be captured and stored

is 704 x 480 (NTSC for the United States) and 720 x 576 (PAL for Europe). This resolution is known as D1

resolution. A high end CCTV recorder is capable of recording at up to D1 resolution.

CCTV Resolutions

D1: 704 x 480

HD1 (2CIF): 704 x 240

CIF: 352 x 240

QCIF: 176 x 120

Motion Detection Main Screen

Motion Detection Sensitivity Screen

Indicates motion record is enabled.

Indicates motion detected.

Alarm Setting Screen

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

First Alert PRO16810-600CA Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info