Bedienungsanleitung First Alert PRO8810-600CA (Seite 25 von 47) (Englisch)

795187

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

Page 25

Pan tilt zoom...PTZ

Pan/Tilt/Zoom (PTZ) Setup:

Note: Consult the instruction manual of your PTZ

camera for complete information about your camera,

including protocol, baud rate and parity settings before

beginning setup. Enter these settings in the DVR.

STEP 1: Connect your PTZ Camera to this DVR

Connect a PTZ camera to the BNC and DC power cables. Also,

connect the communication cable from the PTZ camera to the

485A (TX, +) and 485B (RX, -) control inputs to the PTZ block on

the back of the DVR. Note there is only one set of PTZ control

inputs (485A & 485B), however multiple PTZ cameras can be set

up by making parallel connections. See diagram for details and

see “PTZ Camera Setup” Info box for additional information.

PTZ Camera Setup

NOTE: It is recommended for best results to use

120Ω shielded twisted pair cable of a sufﬁcient

gauge to meet your application length. 18 to 22

gauge is usually sufﬁcient. In addition, be sure to

only install the 120Ω terminating resistor that comes with your

PTZ camera in the last parallel connected camera. Keeping that

resistor in all cameras can possibly degrade the signal and can

cause unexpected or loss of operation and control.

Step 2: Conﬁgure PTZ Communication Settings

To access this menu, from the setup menu click DEVICE. Then PTZ.

This will bring up the PTZ setup screen. PTZ setting options for each

camera can be selected independently for each camera channel

1. Select the appropriate channel connected to the PTZ camera using

the drop down

2. Under ADDRESS, enter an address from 001–255 using the virtual

keyboard

3. Under protocol, select the appropriate protocol based on the

setting of the camera using the drop down menu (PELCO-D,

PELCO-P, PELCO-D EXT, PELCO-P EXT, PELCO-D-3)

4. Under BAUD rate, select 1200, 2400, 4800, 9600 as set in the PTZ

camera

5. Click OK to conﬁrm settings. Click EXIT to leave screen without

making changes

LEFT/RIGHT, UP/DOWN, IRIS ZOOM, FOCUS ZOOM and

ZOOM EXCHANGE will reverse the actions taken when

moving or zooming the camera. For example movement

to the left, becomes movement to the right and movement

to zoom in is reversed to movement to zoom out.

Note: Changes to the PTZ setup screen take place immediately.

However, in the event of a power failure, the settings can

revert to the previous settings. It is recommended to perform

a power down and restart through the drop down menu to

save changes in order for the system to operate with these

changed PTZ setting should a power failure occur.

Pan tilt zoom...PTZ continued

Install 120 Ω

terminating

resistor in last

camera only

AB AB AB

PTZ Inputs Conguration

RS485

– +

–

ADVANCED OPERATION

PTZ

PTZ Setup Screen

PTZ Manual Control Screen

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

First Alert PRO8810-600CA Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info