Bedienungsanleitung First Alert 9120B (Seite 4 von 7) (Englisch)

795069

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

OPTIONAL LOCKING FEATURES

The optional locking features are designed to discourage unauthorized removal of the battery or alarm. It is not necessary to activate the locks in

single-family households where unauthorized battery or alarm removal is not a concern.

These Smoke Alarms have two separate locking features: one to lock the battery compartment, and the other to lock the Smoke Alarm

to the mounting bracket. You can choose to use either feature independently, or use them both.

Tools you will need: • Needle-nose pliers or utility knife • Standard Flathead screwdriver.

Both locking features use locking pins, which are molded into the mounting bracket. Using needle nose pliers or a utility knife, remove one

or both pins from the mounting bracket, depending on how many locking features you want to use.

To permanently remove either lock insert a flathead screwdriver between the locking pin and the lock, and pry the pin out of the lock.

Locking Pin

TO LOCK THE BATTERY COMPARTMENT

(Model 9120B Only)

Do not lock the battery compartment until you have activated

the battery and tested the battery back-up.

1. Activate the battery back-up by removing

the “Pull to Activate Battery Back-Up” tab.

2. Push and hold test button until the alarm

sounds: 3 beeps, pause, 3 beeps, pause.

If the unit does not alarm during testing,

DO NOT lock the battery compartment!

Install a new battery and test again.

If the Smoke Alarm still does not alarm,

replace it immediately.

3. Using needle-nose pliers or a utility

knife, detach one locking pin from

the mounting bracket.

TO UNLOCK THE BATTERY COMPARTMENT

(Model 9120B Only)

Once the Smoke Alarm is installed, you must disconnect it from the AC power

before unlocking the battery compartment.

ELECTRICAL SHOCK HAZARD. Turn off the power to the area where the

Smoke Alarm is installed before removing it from the mounting bracket.

Failure to turn off the power first may result in serious electrical shock,

injury or death.

Always discharge the branch circuit before servicing an AC or AC/DC

Smoke Alarm. First, turn off the AC power at the circuit breaker or fuse

box. Next, remove the battery from Smoke Alarms with battery back-up.

Finally, press and hold the test button for 5-10 seconds to discharge the

branch circuit.

1. Remove the Smoke Alarm from the mounting

bracket. If the unit is locked to the bracket, see

the section “To Unlock the Mounting Bracket.”

2. Disconnect the power connector by gently prying

it away from the back of the Smoke Alarm.

3. Insert a flathead screwdriver under the head of

the locking pin, and gently pry it out of the bat-

tery compartment lock. (If you plan to relock the

battery compartment, save the locking pin.)

4. To relock the battery compartment, close the battery door and reinsert

locking pin in lock.

5. Reconnect the power connector to the back of the Smoke Alarm, reattach

the Smoke Alarm to the mounting bracket, and restore the power.

When replacing the battery, always test the Smoke Alarm before relocking the

battery compartment.

TO UNLOCK THE MOUNTING BRACKET

ELECTRICAL SHOCK HAZARD. Turn off the power to the area where the

Smoke Alarm is installed before removing it from the mounting bracket.

Failure to turn off the power first may result in serious electrical shock,

injury or death.

Always discharge the branch circuit before servicing an AC or AC/DC

Smoke Alarm. First, turn off the AC power at the circuit breaker or fuse

box. Next, remove the battery from Smoke Alarms with battery back-up.

Finally, press and hold the test button for 5-10 seconds to discharge the

branch circuit.

1. Insert a flathead screwdriver between the mounting bracket pin and the

mounting bracket.

2. Pry the Smoke Alarm away from the bracket by turning both the screw-

driver and the Smoke Alarm counterclockwise (left) at the same time.

TO LOCK THE MOUNTING BRACKET

1. Using needle-nose pliers or utility

knife, detach one locking pin from

mounting bracket.

2. Insert the locking pin into the

lock located on the base as

shown in the diagram.

3. When you attach the Smoke

Alarm to the mounting

bracket, the locking pin’s

head will fit into a notch on

the bracket.

4. Push the locking pin through the

black dot on the label on the back

of the Smoke Alarm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

First Alert 9120B Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info